Width of Trailer Axle e25GR With Kenda Tire & Wheel AM30790

Question

Question:

Im looking to buy axle# e25GR. If I buy 2 tires #AM30790... What would the width from outside edge to outside edge of the tires be ? Im trying to fit in between trailer frame rails of 71

asked by: Greg

0

Expert Reply:

I'm happy to say they will be able to fit. The reason is the total width is 65.6" from outside to outside with the Trailer Axle with Idler Hubs # e25GR and two of the Kenda 5.30-12 Bias Trailer Tire with 12" Galvanized Wheel # AM30790.

expert reply by: Kyle S

0

Answer 1

Hey Caleb, unfortunately you can't use slipper springs with a radius end like the 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles #e99SR because the brackets are different. You could use open eye springs like #e24SR to replace your…

view full answer...

Answer 2

You will want to remove your spring hangers and then weld them in a position that allows the shackles to hang properly. On a spring that is 26 inches eye to eye on center and a single axle trailer you will want the hangers to be up to 1/2 inch less…

view full answer...

Answer 3

When using the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles part #e27SR with the Single-Axle Trailer Hanger Kit for Double-Eye Springs part #APS4 you will need to space the leaf spring hangers 25-3/4" apart.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Width of Trailer Axle e25GR With Kenda Tire & Wheel AM30790

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching