Will You Need to Re-Wire a Boat Trailer In Order to Switch to LED Lights
Updated 07/07/2023 | Published 07/06/2023
Products Featured in This Question
Question:
I am needing to replace older candescent bulbs with LED on my boat trailer. Previously had: Wesbar 105826 saeaip2st-dot-94 I see some replacements for that light on this site BUT wanted to know if I need to rewire the entire trailer since switching to LED? Or can the new LED lights just plug and play? Thank you in advance!
asked by: Lars
Expert Reply:
No, you should not need to rewire your whole trailer just to switch to LED lights. Unless you get into doing the swap and discover your wiring is damaged, it should be as easy as mounting the new lights and wiring them in.
The LED Tail Light # STL37RB (driver side) and LED Tail Light # STL36RB (passenger side) are great choices to replace your Wesbar 105826 lights. These lights are submersible and splice into your wiring in place of your old lights.
Product Page this Question was Asked From
LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 23 Diodes - Driver Side
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- License Plate
- Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 8L x 3W Inch
- Red
- Optronics
more information >
Continue Researching
- Q&A: LED Replacement Lights for a Boat Trailer with Wesbar 105826 Tail Lights
- Search Results: wesbar~trailer~lights
- Search Results: axle cotter pin
- Search Results: marine grade trailer hubs and drums
- Search Results: idler hub assembly
- Search Results: etrailer trailer hubs and drums
- Search Results: cotter pin
- Shop: LED Tail Light for Trailers Over 80" Wide - 7 Function - Submersible - 17 Diodes - Passenger
- Shop: LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 23 Diodes - Driver Side
- Shop: LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 23 Diodes - Driver Side
- Video: A Closer Look at the Right Angle 3-Wire Pigtail for Optronics Trailer Lights
- Shop: Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Q&A: What Does LRD Mean On Trailer Tire
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Gorilla Retractable Ratchet Straps - S-Hooks - 1" x 16' - 500 lbs - Qty 2
- Shop: SmartStraps Retractable Ratchet Tie-Down Straps - 1-1/4" x 10' - 1,000 lbs - Qty 2
- Video: All You Need to Know About the Gorilla Retractable Ratchet Straps
- Video: SmartStraps Retractable Ratchet Tie-Down Straps: The Breakdown
- Video: An In-Depth Look at the SmartStraps Retractable Ratchet Tie-Down Straps
- Article: Trailer Wiring Diagrams
- Q&A: Replacement Hub for Tie Down Engineering 11033
- Q&A: Replacement Trailer Hub Assemblies For 3,500LB Axles Using L68149 Inner and L44649 Outer Bearings
- Search Results: spindle cotter pin
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Video: 3500lb Trailer Idler Hubs Direct Comparison
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Idler Hub - AKIHUB-545-35-EZ-K
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Shop: Trailer Wiring
on Trailer Lights
