Replacement Awning Arms for a Lippert Edge Awning

Question

Question:

Lippert Replacement Black Support Arm Assembly For Edge 58 Inch Awning - LC77VR do you have this? can not find on your site.

asked by: Dave F

0

Expert Reply:

The Replacement Support Arm Assembly for Lippert Edge 58" Awning LC77VR has been discontinued, however we do have it's replacements the Replacement Drive Arm Assembly for Lippert Edge RV Awnings with LEDs # LC22ED and the Replacement Idler Arm Assembly for Lippert Edge RV Awnings with LEDs # LC62ED.

Both of these parts will work great with your Lippert Edge awning and measure the same 58" as the previous did.

expert reply by: Bryce D

0

Cecil D.

2/16/2024

Do they come in black

Answer 1

Since your Solera arm is 58 inches long that would indicate it's a Solera Edge awning which means for a replacement drive arm you would want the part #LC22ED or for a replacement idler arm part #LC62ED.

view full answer...

Answer 2

In order to determine the correct replacement for your Lippert Edge awning you'll need to measure the length of your wall mount (see attached photo). Once you've got that number you can look for a replacement based off of that measurement.…

view full answer...

Answer 3

Hi Jesus, The number you provided comes back as a Solera Edge awning in black, but we'll need a bit more information to determine the correct arm because there's 3 different models in black. There should be another sticker on the arm with a…

view full answer...

Answer 4

For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part #LC62ED and the correct replacement drive arm (one with the motor) is the part #LC22ED.

view full answer...

Answer 5

Thank you for providing your part number Steve. I was able to verify you will need the Replacement Idler Arm Assembly #LC75AF. We also have the Replacement Drive Arm Assembly #LC85AF.

view full answer...

Answer 6

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 7

Since you said you have the 58 inch arms that would indicate that you have the Lippert Edge awning which we have just the replacement arms for. For the idler arm you'd want the part #LC62ED and for the driver arm part #LC22ED.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 11

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 12

Hi Nathaniel, Great choice on switching to the Furrion Chill 18,000 BTU! You're going to love the performance and efficiency it brings. One of the biggest advantages of the switch is that Furrion has upgraded their refrigerant from R410A to the…

view full answer...

Replacement Awning Arms for a Lippert Edge Awning

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching