Spare Tire Carrier Option For Tow Dolly

Question

Question:

Looking for a spare tire mount and will be using a tow dolly

asked by: Thomas H

0

Expert Reply:

The only option we have for a spare tire carrier while using your tow dolly is if your tow dolly has a max 4" tall tongue; if it does what you can use is the Demco Spare Tire Carrier for up to 4" Tall Trailer Tongue # DM15851-76.

This will fit tires with bolt patterns from 4 on 4" to 8 on 6-1/2".

expert reply by: Kyle S

0

Answer 1

If the tow dolly uses ST rated tires (which most likely it does), then you need to keep the tire pressure at it's max psi to ensure you get the full capacity and prevent heat buildup. You will know if the tire is ST rated by checking out the size…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Spare Tire Carrier Option For Tow Dolly

Product Page this Question was Asked From

Continue Researching