Load Roller Kit Needed for Malone Axis Truck Bed and Roof Load Extender

Question

Question:

I cannot find the roller kit for the Malone Axis load extender MPG907

asked by: Russ

0

Expert Reply:

To add a roller to the Malone Axis Truck Bed and Roof Load Extender for 2" Hitches # MPG907 you need the part # MAL97AR which comes with the roller and the mounting hardware to install it.

expert reply by: Jon G

0

Answer 1

Hello Jim, Great question, I went to Malone's site and and I do not see that they make one with a 48" roller. The great thing about the Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR is that it is adjustable, the…

view full answer...

Answer 2

At this point in time we haven't had the chance to install the Yakima LongArm Truck Bed Load Extender #Y01149 on a 2019 Ford Ranger, but we do have some dimensions on it that I think will be useful to you. If you check out the attached…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The Yakima LongArm Truck Bed Load Extender #Y01149 is a great solution for hauling a longer kayak with your 2019 Ford F-150 5-1/2' bed. When in the fully-extended position the LongArm sits out 48" from the center of your hitch pin hole which…

view full answer...

Answer 7

Thanks for reaching out Kaiya, happy to help! For the 1998 Chevy C1500 Stepside, drilling is not required to install the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-FMC2576. On Stepside models, the cover uses the factory…

view full answer...

Answer 8

Hi Steven, Based on your setup, the Roadmaster Anti Rattle Hitch Extender part #RM-071-1075 could potentially give you the additional clearance you need between the bike rack and tow bars, but I want to make sure we get this right before recommending…

view full answer...

Answer 9

Hey Rick, I can't speak for Malone but we measured from the top of the hitch opening to the top of the Malone Axis part #MPG907 and found the height range to be between 15 and 22 inch. I also made sure that when we took this measurement it was…

view full answer...

Answer 10

Thanks for reaching out! The Rhino-Rack roof rack for your 2022 Mazda CX-5 is a great selection that I know you'll be happy with, and it includes the parts you referenced: 46" Vortex Crossbars - #RRVA118B-2 RCL Legs - #RRRCL4 RCP Fit Kit -…

view full answer...

Answer 11

Hey Martin, so you did your homework on this but yes you can use the Telos lift assist part #MPG351XL with your Yakima JayLow kayak carrier as long as you also get the universal roof rack adapter part #MAL95VR. This adapter would give you the…

view full answer...

Load Roller Kit Needed for Malone Axis Truck Bed and Roof Load Extender

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching