Bearing Kit and Grease For Repacking Bearings On a 2022 Brand Design Imagine 2400BH Travel Trailer

Question

Question:

I have a 2022 Imagine 2400BH and will be repacking bearings. I need to buy a kit for one axle as a standby in case I have to replace components. What bearings and seals do I need? Thanks

asked by: Jaime H

0

Expert Reply:

The Hub Bearing Kit # BK2-100 is the correct kit for the 3,500lb axles on your 2022 Grand Design Imagine 2400BH. This provides the bearings, races and a grease seal for 1 hub. We do have the Seal Puller # PTW1219 and Bearing Packer # PTW1218 to make repacking the bearings much easier. I recommend using the Grease # L11390 and Grease Gun # L30416 to fill the bearings. This grease is designed for use in extreme temperatures and pressures and is highly water resistant.

expert reply by: Bud M

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 11

Hey Gary, What I'm seeing is that your 2010 Harmony 21FBS will have 3,500 lb axles so you need the Hub Bearing Kit #BK2-100. I wasn't able to find anything definitive about this though, so I do recommend checking the sticker in the middle of…

view full answer...

Bearing Kit and Grease For Repacking Bearings On a 2022 Brand Design Imagine 2400BH Travel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching