Trailer 4-Way Wiring Harness that Fits 2018 Chevy Express 2500 Van

Question

Question:

Im looking for a trailer wiring t-harness for a 2018 chevy express 2500 cargo van. Any advice would be greatly appreciated.

asked by: Shane S

0

Expert Reply:

For your 2018 Chevy Express van 2500 we have the Curt trailer wiring kit # 55540 that's a confirmed fit and would work great. It's a t-connector style harness that installs by plugging inline with the taillight connectors of your van.

expert reply by: Jameson C

0

Answer 1

Thanks for the picture Don! I do not have anything that connects to that 10-pin so I am hoping you're just at the wrong connector. I have linked a picture below along with an installation video that will show you what the Hopkins item #31345…

view full answer...

Answer 2

The 2018 Chevy Express Van does have the brake controller wiring existing to wire in the brake controller if it has the towing package but that does not mean all of the wires are extended to the back of the vehicle. There may be a round plug with a…

view full answer...

Answer 3

Thank you for all of the information and pictures! It looks like you should at least have some wiring already run on your 2019 Chevy Express Van 3500 so I'm just as confused as to why you don't have a round plug with a cap inside the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Trailer 4-Way Wiring Harness that Fits 2018 Chevy Express 2500 Van

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching