Dutton-Lainson Square Swivel Jack Mounting Plate Bolt Pattern I will be us

Question

Question:

What is bolt pattern for mounting? I will be using a welded mounting plate on my trailer to attach

asked by: Bob

1

Helpful Expert Reply:

The Dutton-Lainson Square Swivel Jack # DL22340 has a mounting plate designed to fit trailer frames with a height of 3" - 5". I have attached a dimensional drawing below with all of the bolt spacing for your reference.

expert reply by: Robin H

1

DL22340 Bolt Pattern.
(click to enlarge)

Answer 1

Hi Jeff; the Dutton-Lainson Boat Trailer Jack w/ Wheel #DL22339 is designed to fit a 3" tall x 4" wide trailer tongue. It is possible to use it with a 5" wide trailer tongue but you will likely need to acquire longer bolts locally to…

view full answer...

Answer 2

Hey Scott, double towing gets a little tricky but what I would probably do is use a wireless brake controller like the Curt Echo Mobile #C51180 on the second trailer as that would be the only reasonable way to activate a second controller since the…

view full answer...

Answer 3

The Fulton F2 Swing-Up Trailer Jack with No Mounting Hardware #F1413100334 referenced in your question features a bolt pattern that is 3-3/8 inches on center x 4-3/8 inches on center. There is not a Fulton jack currently available that includes a…

view full answer...

Answer 4

The Dutton Lainson jack part #DL22340 has a wider bracket than the what a Fulton F2 jack would have so you'd have to remove the Fulton bracket so you could install this jack in it's place.

view full answer...

Answer 5

I attached a picture that has the measurements of the mounting holes on the mounting plate of the Dutton Lainson Sidewind jack #DL22339 that you referenced. Basically they are 5-1/2 inches from left to right and then 2-3/8 top to bottom row and then…

view full answer...

Answer 6

Hello again, Alex. Both the Dutton-Lainson #DL22457 and Fulton F2 part #F1413140334 are good jacks but between those two the Fulton F2 is the better quality option as far as quality, durability and serviceability. The Fulton F2 is made of a coated…

view full answer...

Answer 7

I do have an option, but the Dutton Lainson Square Swivel Jack #DL22340 you were looking at will not bolt directly to the welded mount on your trailer that your current Fulton F2 trailer jack is bolted to. With that being said as long as your trailer…

view full answer...

Answer 8

The Prodigy RF brake controller part #TK94FR requires being connected to a 7-way trailer connector that has taillight circuits that are combined on the brake lights and turn signals. As well as has to have a 12 volt power circuit that is active too.…

view full answer...

Answer 9

I think in an absolutely ideal world you'd have two brake controllers so that you could set the max braking pressure individually but in reality that would be really involved to pull off and you'd get solid results with just a single brake…

view full answer...

Answer 10

In order to use the Tekonsha Prodigy RF Wireless Trailer Brake Controller part #TK94FR on a vehicle with another brake controller already installed all you need to do is unplug the connector from the back of the other brake controller. You will not…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Dutton-Lainson Square Swivel Jack Mounting Plate Bolt Pattern I will be us

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching