Replacement Pin for Yakima Swing Daddy Bike Rack

Question

Question:

I need a Yakima pull pin replacement but I do not know my swing out style racks name or model. But I do know the pull pin is 3/8” diameter. Do you have a 3/8” diameter pull pin for a Yakima rack?

asked by: Bryce W

0

Expert Reply:

Looks like you have an older Yakima SwingDaddy so the correct replacement spring pin would be the part # 8890314.

If instead you are looking for a replacement hitch pin that secures it to the trailer hitch you would want the part # 889-0231

expert reply by: Jameson C

0

Yakima Swing Daddy
(click to enlarge)

Answer 1

Hey Chris, thanks for all of the information and photos! The part you're wanting for your older Yakima FullSwing 4 (8002403) is the kit 8780024, but it has been discontinued by Yakima so the only way you'll be able to get that exact setup is…

view full answer...

Answer 2

You are right, I pulled both the part #Y8890185 and the #Y8780022 from our warehouse and the only difference is the additional flat washer that is in the #Y8890185.

view full answer...

Answer 3

The Yakima Threaded Hitch Bolt, part #Y8890200 is 5/8 inch in diameter and a 4-1/4 inch overall length, as shown in the provided photo. The StickUp originally included two different hitch bolts, one for the 2 inch hitch and a shorter one for the…

view full answer...

Answer 4

The Yakima SwingDaddy-specific straps are #8890221 for three. The holes in these straps are 1/2 inch in diameter so you could really use any strap with 1/2 inch diameter holes. You could get a set of 4 Thule straps using #TH534 if you prefer. There…

view full answer...

Answer 5

The Replacement ZipStrip Straps #Y8890297 are the correct fit for your Yakima FullSwing 4 Bike Rack #Y02465.

view full answer...

Answer 6

The hitch bolt included in the Yakima Replacement Mounting Hardware for SwingDaddy Hitch Mounted Carrier #Y8890185 measures exactly 4.28 inches long with a 1/2 inch diameter and 13 pitch. If you only need the bolt and clip you can use part…

view full answer...

Answer 7

It looks like you purchased the Replacement Mounting Hardware, #Y8890185. This should have come with the square, black shank insert, a square nut that fits inside of the shank insert, a flat washer, a lock washer and a threaded pin and clip. I made a…

view full answer...

Answer 8

Hey Carissa, we do have the replacement Thule part you are looking for with the Yakima part number #Y8890176.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Replacement Pin for Yakima Swing Daddy Bike Rack

Product Page this Question was Asked From

Continue Researching