What Position Must The Kwikee Revolution Steps Be In When Replacing The Motor # LC380073?

Question

Question:

I just ordered part# LC380073 for my 2022 winnebago M/H. After I receive my part when installing it, does the steps have to be fully extended for the gear on the motor to mesh with the gear on the step, or doesnt it matter? The M/H is a 2022 winnebago adventurer 30T Thanks

asked by: Howard M

0

Expert Reply:

When replacing the Motor # LC380073 on your Kwikee Revolution Steps # LC3725791 you need to use a jack or another object to hold the steps in the retracted position.

expert reply by: Bud M

0

Answer 1

Hey Craig! Everything is switching over to the new R32 refrigerant right now. These new systems are not backwards compatible so you can't simply add the #FR86TD to your existing setup. Also, we no longer recommend swapping just the AC unit since…

view full answer...

Answer 2

Hey Greg! If you're ok with black for the color you can swap out the AC unit with the Furrion Chill HE Replacement RV Air Conditioner Unit for Furrion Setup #FR86PR. This is an old R410A unit so it will be compatible. All of our old white units…

view full answer...

Answer 3

According to Lippert, the correct replacement for your model 9010000464 Kwikee Revolution Steps is the Replacement Steps, Motor, and Control for Kwikee RV Electric Steps - Revolution Series #LC3725791. If you want the complete assembly with the…

view full answer...

Answer 4

Hey Andrew, the only solution for what you have is the part #LC3725791 which does come with more than what you need but there isn't just a bare frame like you mentioned.

view full answer...

Answer 5

While I could not get the video to play, it sounds more like a control unit issue rather than a motor issue. The control unit should sense when the steps are closed and shut off the power for retracting and not spasm. Since you mentioned so many…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

What Position Must The Kwikee Revolution Steps Be In When Replacing The Motor # LC380073?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching