2004 Alpenlite 5th Wheel Landing Gear Replacement Recommendation

Question

Question:

Both landing jacks have their own motors. The driver side one has failed the motor has broken loose from the jack. Due to the age of the camper, I may as well replace both sides. Do you have suggestions as to parts needed? Measurements for ordering parts, ect.... Thank you,

asked by: Chad P

1

Helpful Expert Reply:

For your 2004 Alpenlite 5th Wheel the Lippert landing gear set part number LC333964 would be a really great option. This would fit the standard landing gear bracket dimensions you have and would work quicker than other options as it has a higher 6k capacity.

expert reply by: Jameson C

1

Answer 1

Hey Peter, do you have a Lippert Ground Control leveling system on your Keystone Montana? If so, the part number you mentioned most closely corresponds with the replacement right rear leg part #LC428493. If instead this is a standard landing gear…

view full answer...

Answer 2

Hello Keith, Yes, there are repair kits. I do not have a database that I can reference to see what was put on what camper. On my search I see that the Lippert Venture is the common lading gear on the 2003 Montana, for the follow leg (leg without the…

view full answer...

Answer 3

Since your Venture leg is the follow leg the repair kit is #LC146060. If you had the lead leg it would be #LC146059.

view full answer...

Answer 4

Your 2000 Jayco Eagle likely uses either Stromberg Carlson Electric Landing Gear Set #LG-1 or a Lippert setup like Lippert Electric Landing Gear Set #LC333964. You will want to confirm this, but if you need the replacement lead leg for Stromberg…

view full answer...

Answer 5

Yes, you can use Lippert lead leg #LC179013 and follower leg #LC179014 to replace the legs on your Fulton system. Many landing gear parts on newer 5th wheel trailers like yours are interchangeable.

view full answer...

Answer 6

I did some checking and the 2009 Heartland Bighorn 5th wheel trailers were built on a Lippert chassis and have other Lippert components so the landing gear will also be Lippert. If you just need to replace legs then the lead leg is #LC179013 and the…

view full answer...

Answer 7

We do have the measurements for the Replacement Lead Leg for a KeyStone Montana Trailer #LC178653. I went ahead and attached a picture of the dimensions to this answer. Even though this leg has three bumps, it will still work to replace the lead leg…

view full answer...

Answer 8

I attached a picture that shows where the zerk fitting for greasing the Lippert landing gear part #LC179013 is, but if your landing gear does not have any fittings best bet would be to take off the top (if possible) and apply grease to the bevel…

view full answer...

Answer 9

There is a great chance either of the legs you mentioned would work as a replacement, but I'd need to know for sure what landing gear you have on your trailer. The Lippert landing gear like the part #LC179013 and #LC179014 are very popular and…

view full answer...

Answer 10

In order to get the correct replacement drop leg you will need to know the manufacturer and model of your current landing gear because they do need to match in order to keep your Heartland Sundance level. For example, the Replacement Lead Jack w/…

view full answer...

Answer 11

My contact at Lippert Components confirmed that their manual landing gear #LC333966 can indeed be converted to powered operation later on through use of their motor kit #LC142178 and switch kit #LG-145236. You can use the same gearbox that comes with…

view full answer...

Answer 12

I can give you some information to help you determine if the Lead #LC179013 and Follow #LC179014 legs will fit your 2004 Arctic Fox 29.5E 5th wheel, but we don't really have a database to pull from when it comes to OEM part numbers on trailers.…

view full answer...

2004 Alpenlite 5th Wheel Landing Gear Replacement Recommendation

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching