Difference Between Lippert Components 32" Lead and Follow Legs

Question

Question:

What is the difference between landing leg 179013 and 179014

asked by: Dave J

0

Expert Reply:

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin # LC179013 is the lead leg, or the one that the gearbox and handle will attach to, while the Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs # LC179014 is the follow leg, which connects to the drive leg via a cross shaft.

So the leaf leg has the gearbox on it while the follow leg is just attached to the lead leg with a cross shaft.

expert reply by: Jon G

0

Answer 1

Hey Peter, do you have a Lippert Ground Control leveling system on your Keystone Montana? If so, the part number you mentioned most closely corresponds with the replacement right rear leg part #LC428493. If instead this is a standard landing gear…

view full answer...

Answer 2

I spoke with my contact at Lippert who acquired Venture and he said that repair kit #LG-146059 is the correct kit for lead leg and then part #LC146060 for the follow leg.

view full answer...

Answer 3

There is a great chance either of the legs you mentioned would work as a replacement, but I'd need to know for sure what landing gear you have on your trailer. The Lippert landing gear like the part #LC179013 and #LC179014 are very popular and…

view full answer...

Answer 4

Take the top off of the jack leg and inspect the bevel gears that you can see. If they look damaged all you'd need is the repair kit part #LC146060. If other components look damaged it would be best to replace the entire leg with part…

view full answer...

Answer 5

My contact at Lippert Components confirmed that their manual landing gear #LC333966 can indeed be converted to powered operation later on through use of their motor kit #LC142178 and switch kit #LG-145236. You can use the same gearbox that comes with…

view full answer...

Answer 6

Yes, you can use Lippert lead leg #LC179013 and follower leg #LC179014 to replace the legs on your Fulton system. Many landing gear parts on newer 5th wheel trailers like yours are interchangeable.

view full answer...

Answer 7

In order to get the correct replacement drop leg you will need to know the manufacturer and model of your current landing gear because they do need to match in order to keep your Heartland Sundance level. For example, the Replacement Lead Jack w/…

view full answer...

Answer 8

If the damage looks to be part of the follow leg itself, then your best bet is to replace the entire leg. We have a large selection of replacement follow legs available, which I have attached below. I recommend searching for a model number somewhere…

view full answer...

Answer 9

Hey Kerry, I don't have the ability to look up parts for your trailer, only Jayco would be able. There should be some sort of branding or serial number on the lead leg or motor that we can use to try and identify it. We do offer the lead leg and…

view full answer...

Answer 10

For your 2004 Alpenlite 5th Wheel the Lippert landing gear set part number LC333964 would be a really great option. This would fit the standard landing gear bracket dimensions you have and would work quicker than other options as it has a higher 6k…

view full answer...

Answer 11

In order to find the correct replacement landing gear legs for your 2013 Keystone Laredo 335TG I would need you to take two quick measurements of your existing landing gear legs, the outer tube length and weld stop spacing. I have attached a photo to…

view full answer...

Answer 12

Replacement leg #LC178653 is unique to the Keystone Montana. Your 2004 Keystone Challenger likely uses a different lead leg, #LC179013. But it will depend on where the stops are located on the existing leg. The stops are the protrusions that stick…

view full answer...

Difference Between Lippert Components 32" Lead and Follow Legs

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching