Correct Replacement Master Cylinder for DICO Surge-O-Matic Model 10 Surge Brake Actuator

Question

Question:

will #dx66fr fit DICO surge-o-matic model 10 surge brake

asked by: Brad

1

Helpful Expert Reply:

Yes, the Replacement Master Cylinder and Push Rod Assembly for Drum Brakes part # DX66FR fits the DICO Surge-O-Matic Model 10 Surge Brake Actuator.

expert reply by: Conner L

1

Answer 1

I pulled both the #DX66FR and the #T4747100 that you referenced to check out and found a way for you to determine which you have. You will need to remove the red plug from the end opposite of the plunger and look down into that hole. If you see what…

view full answer...

Answer 2

The Master Cylinder for Titan Actuators - Disc Brakes #T4747100 is 1/2 inch-20 female so you will need the Orifice Connector for Titan Actuators #T1209800 which fits the inverted flare. Replacement Brass Connector for Titan Disc Brake Actuators - Qty…

view full answer...

Answer 3

Thanks for the photos of your trailer's actuator! They were very helpful in answering your questions. Based on the photos, it appears that you have a Titan Model 10 Actuator #T1607500. For a Model 10 actuator, the #DX66FR that you referenced is…

view full answer...

Answer 4

You can view drum brake surge couplers for 2-5/16-inch balls by clicking on the linked page. Simply click on the filters to select the features you want, such as weight rating, bolt-on versus weld-on installation, and a-frame or straight tongue…

view full answer...

Answer 5

Hey Woody, The master cylinder you have is a Titan #23744, or a Titan 10/20 brake actuator, and we do have a replacement for you. The replacement is going to be part #DX66FR. This is made by Dexter, but is a direct replacement for your master…

view full answer...

Answer 6

The Replacement Master Cylinder #DX66FR is the replacement for the 23744. This master cylinder will include a new Cap #T4830601 and we do have the Replacement Shock #T1242600 for your Titan 12426.

view full answer...

Answer 7

The Master Cylinder for Model 10 and 20 Actuators #DX66FR has 3/8-inch mounting holes spaced apart on centers by 3-7/16-inches. I measured this item myself in our warehouse.

view full answer...

Answer 8

I spoke with my contact at Dexter, and the #DX66FR master cylinder does include the boot and push rod, but their design does not require the gasket. Please note that this master cylinder is a replacement part only for the Titan brand Model 10 and…

view full answer...

Answer 9

I spoke with my technical contact at Titan and showed him the photo that you sent in of your actuator. My contact confirmed that you actuator is a Model 60. The right replacement master cylinder for you will depend on what kind of brakes the actuator…

view full answer...

Answer 10

Look at the top of the master cylinder and you'll be able to tell which type of brakes it is designed for by the whether there is a yellow dot or not. If you see the yellow dot then you have a disc brake setup. If no yellow dot then drum. Also…

view full answer...

Answer 11

The Master Cylinder #DX66FR is for Titan Model 10 and 20 Actuators; so if this cylinder works then you have a Titan Model 10 or 20 and the correct Replacement Master Cylinder Cap is part #T4830601.

view full answer...

Answer 12

Yes, the Replacement Solenoid Adapter Fitting for Titan Model 10 Brake Actuators, part #T4750200, is for pre-2000 Titan Model 10 brakes. If you have a newer Titan Model 10 brake, you will use the Orifice Connector for Titan Actuators Item #T1209800.…

view full answer...

Correct Replacement Master Cylinder for DICO Surge-O-Matic Model 10 Surge Brake Actuator

Product Page this Question was Asked From

Continue Researching