Mounting Hole Diameter and Spacing on Master Cylinder DX66FR

Question

Question:

Would have the measurement from center to center between the two mounting holes on DX66FR?

asked by: Jim

0

Expert Reply:

The Master Cylinder for Model 10 and 20 Actuators # DX66FR has 3/8-inch mounting holes spaced apart on centers by 3-7/16-inches. I measured this item myself in our warehouse.

expert reply by: Adam R

0

Answer 1

We do have the Titan master cylinder replacement part #DX66FR which has the number 23744 stamped on the side of it. See attached picture. A lock out solenoid would attach directly to the back of the master cylinder without an adapter. If you are in…

view full answer...

Answer 2

To replace the master cylinder on your Titan 10 brake actuator you can check out the diagram of the actuator I have attached. In the diagram there are two bolts that are noted you need to loosen to get to the master cylinder. They are part number 20…

view full answer...

Answer 3

Yes, the Replacement Master Cylinder and Push Rod Assembly for Drum Brakes part #DX66FR fits the DICO Surge-O-Matic Model 10 Surge Brake Actuator.

view full answer...

Answer 4

The Master Cylinder #DX66FR is for Titan Model 10 and 20 Actuators; so if this cylinder works then you have a Titan Model 10 or 20 and the correct Replacement Master Cylinder Cap is part #T4830601.

view full answer...

Answer 5

The Replacement Master Cylinder #DX66FR is the replacement for the 23744. This master cylinder will include a new Cap #T4830601 and we do have the Replacement Shock #T1242600 for your Titan 12426.

view full answer...

Answer 6

The Master Cylinder for Titan Actuators - Disc Brakes #T4747100 is 1/2 inch-20 female so you will need the Orifice Connector for Titan Actuators #T1209800 which fits the inverted flare. Replacement Brass Connector for Titan Disc Brake Actuators - Qty…

view full answer...

Answer 7

I pulled both the #DX66FR and the #T4747100 that you referenced to check out and found a way for you to determine which you have. You will need to remove the red plug from the end opposite of the plunger and look down into that hole. If you see what…

view full answer...

Answer 8

The correct replacement master cylinder for a Titan Model 10 Brake Actuator is part #DX66FR for drum brakes or part #T4747100 for disc brakes. It is possible that the wrong actuator was installed on the trailer and since the master cylinder is the…

view full answer...

Answer 9

Hello Bill, sounds like you are on the right track. The Replacement Master Cylinder and Push Rod Assembly for Drum Brakes - Model 10 and 20 Actuators #DX66FR will indeed work as a replacement for your Dico model 20 surge brake actuator. We have…

view full answer...

Answer 10

Thanks for the photos of your trailer's actuator! They were very helpful in answering your questions. Based on the photos, it appears that you have a Titan Model 10 Actuator #T1607500. For a Model 10 actuator, the #DX66FR that you referenced is…

view full answer...

Answer 11

I spoke with my technical contact at Titan and showed him the photo that you sent in of your actuator. My contact confirmed that you actuator is a Model 60. The right replacement master cylinder for you will depend on what kind of brakes the actuator…

view full answer...

Answer 12

Look at the top of the master cylinder and you'll be able to tell which type of brakes it is designed for by the whether there is a yellow dot or not. If you see the yellow dot then you have a disc brake setup. If no yellow dot then drum. Also…

view full answer...

Mounting Hole Diameter and Spacing on Master Cylinder DX66FR

Product Page this Question was Asked From

Continue Researching