Replacement Master Cylinder Cap for Titan Model 10 and 20 Brake Actuators

Question

Question:

Ive got a newer one of your T2374400 master cylinder actuators on my trailer that I need a replacement filler cap for. My cap looks like the T4480701, but T4830601 is listed as the replacement cap for 10 and 20 actuators. Which one fits my T2374400 actuator?

asked by: Jason

0

Expert Reply:

The Master Cylinder # DX66FR is for Titan Model 10 and 20 Actuators; so if this cylinder works then you have a Titan Model 10 or 20 and the correct Replacement Master Cylinder Cap is part # T4830601.

expert reply by: Kyle S

0

Answer 1

The difference between a disc brake master cylinder and a drum brake master cylinder is a small check valve that is inside of a drum master cylinder but not present in a disc one. Disc brakes require more pressure than drum brakes so there is no…

view full answer...

Answer 2

I spoke with my technical contact at Titan and showed him the photo that you sent in of your actuator. My contact confirmed that you actuator is a Model 60. The right replacement master cylinder for you will depend on what kind of brakes the actuator…

view full answer...

Answer 3

I verified that the distance between the mounting holes center to center on the Master Cylinder for Titan Actuators, #DX66FR, is 3-7/16 inches. This master cylinder is designed to fit Models 10 and 20 Titan Actuators with drum brakes. If the holes of…

view full answer...

Answer 4

Yes, the Replacement Master Cylinder and Push Rod Assembly for Drum Brakes part #DX66FR fits the DICO Surge-O-Matic Model 10 Surge Brake Actuator.

view full answer...

Answer 5

Look at the top of the master cylinder and you'll be able to tell which type of brakes it is designed for by the whether there is a yellow dot or not. If you see the yellow dot then you have a disc brake setup. If no yellow dot then drum. Also…

view full answer...

Answer 6

I pulled both the #DX66FR and the #T4747100 that you referenced to check out and found a way for you to determine which you have. You will need to remove the red plug from the end opposite of the plunger and look down into that hole. If you see what…

view full answer...

Answer 7

The Replacement Master Cylinder #DX66FR is the replacement for the 23744. This master cylinder will include a new Cap #T4830601 and we do have the Replacement Shock #T1242600 for your Titan 12426.

view full answer...

Answer 8

We do have the Titan master cylinder replacement part #DX66FR which has the number 23744 stamped on the side of it. See attached picture. A lock out solenoid would attach directly to the back of the master cylinder without an adapter. If you are in…

view full answer...

Answer 9

Hey Woody, The master cylinder you have is a Titan #23744, or a Titan 10/20 brake actuator, and we do have a replacement for you. The replacement is going to be part #DX66FR. This is made by Dexter, but is a direct replacement for your master…

view full answer...

Answer 10

You can view drum brake surge couplers for 2-5/16-inch balls by clicking on the linked page. Simply click on the filters to select the features you want, such as weight rating, bolt-on versus weld-on installation, and a-frame or straight tongue…

view full answer...

Answer 11

It sounds like you are looking for a Titan Model 10 or 20 master cylinder replacement based on what you listed which we offer with part #T2374400.

view full answer...

Answer 12

To replace the master cylinder on your Titan 10 brake actuator you can check out the diagram of the actuator I have attached. In the diagram there are two bolts that are noted you need to loosen to get to the master cylinder. They are part number 20…

view full answer...

Replacement Master Cylinder Cap for Titan Model 10 and 20 Brake Actuators

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching