Best Ground Clearance Hitch Receiver for Carrying a Bike Rack on a 2013 Toyota highlander

Question

Question:

Hi, looking for a hitch to carry bikes class 2?, no need for wiring harness but those I see seem to drastically reduce ground clearance. Looking to cut a hole in rear bumper. Do I need an oem hitch and do you carry those? Thanks

asked by: Jeff P

1

Helpful Expert Reply:

The best trailer hitch we have for clearance on your 2013 Toyota Highlander is the EcoHitch Hidden Trailer Hitch Receiver # 306-X7137 as it has a crosstube that sits behind the bumper so the only part below the bumper is the 2" hitch receiver (see attached photo). From what I'm seeing there are some OEM hitches that fit in a cutout on your bumper but we don't sell the OEM hitches so the EcoHitch is what you'll want to go with if you go the aftermarket route.

If you don't already have a bike rack I highly recommend checking out the Kuat NV 2.0 Base Bike Rack # BA22B because it has a sleek matte black finish that matches any black trim on your vehicle, it's compatible with a wide variety of bikes, and Kuat made the rack so it's extremely easy to use.

Attached is a review video of the NV 2.0 Base for you to check out.

expert reply by: Jon G

1

EcoHitch Installed on Toyota Highlander
(click to enlarge)

Answer 1

Sometimes hitches can get slightly bent during shipping and this can be fixed by bending the hitch back into place as long as the hitch only has a slight bend to it. If yours isn't lining up I can almost guarantee that is what happened. Some…

view full answer...

Answer 2

I reached out to my contact at EcoHitch and she verified that the Hidden Trailer Hitch Receiver #306-X7137 will fit with the full size spare tire beneath your 2008 Toyota Highlander. You will want to lower/remove the spare during the installation…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Though it will depend on the hitch you have installed, all of the M10 bolts for the Draw-Tite #75726 and 75586 should be torqued to 42 lb-ft. The Curt #13534, which also uses M10 bolts, should be torqued to 48 lb-ft. If you installed an EcoHitch,…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Best Ground Clearance Hitch Receiver for Carrying a Bike Rack on a 2013 Toyota highlander

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching