See what our Experts say about this etrailer Trailer Jack

• A-Frame Trailer Jack that Can Attach to Inside of Trailer Frame
  So the Trailer Valet 5X Swivel Jack # STC-V211 uses brackets to mount to the side of a trailer frame. For a trailer jack that uses the same style of topwind handle and mounting brackets we have the Round Snap Ring Swivel Jack w/ Footplate # TJBB-2001-B which would work well.
  view full answer...
• Will the etrailer Round, Snap-Ring Swivel Jack # TJBB-2001-B Fit on a 2 inch by 5 inch Trailer Frame
  We have several options for a bolt on swivel jack for your trailer with 2 by 5 inch frame (see link). I would recommend the Pull Pin, Easy Swivel Trailer Jack with 8 inch Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson, item # DL22800, for your trailer if the 1500 pound capacity is sufficient for your boat and trailer. These jacks are high quality and designed to fit square tongues up to 3 x 5 inches. The etrailer Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10 1/2 inch Lift - 2,000...
  view full answer...
• Trailer Jack to Avoid Tailgate Clearance Issues
  There are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like # D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the hitch on your vehicle is, the rise or drop of the ball mount for your trailer, if you're using weight distribution or not, and the measurement from the center of the hitch pin hole to the center of the ball hole I can make the best recommendation...
  view full answer...
  
• Light Duty Trailer Jack for Low Clearance
  Thanks for reaching out Phillip. If you're looking for a light duty jack for low ground clearance I'd recommend # TJBB-2001-B. When retracted, this jack will measure 11" from the center of the swivel point to the bottom of the jack foot. This is a topwind jack rated for 2,000 lbs that gives you 10-1/2" of total lift. Where do you tow the SXS most—rocky trails, ranch roads, or paved drives?
  view full answer...
• Is There a Blank Cover Plate Which Can Mount Over Holes For A-Frame Trailer Jack Holes?
  I have never seen a blank cover plate to cover the hole on your trailer A-frame, but you should be able to easily fabricate one out of a steel or aluminum sheet. As an alternative to the Snap Ring Swivel Jack # TJBB-2001-B you could also consider the Ultimate Trailer Jack # 322-RDJ-2K. This jack mounts in the same space as your current A-frame jack and will allow you to lower it to one of 7-different heights to clear your tailgate.
  view full answer...
• Trailer Jack Compatibility with 14 Inch Tongue Space
  The Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson # DL22800 has an overall length of 26-5/8 inches, so it will not fit where you are desiring. The height to the bracket when retracted is 13 inches, but the overall will to too long. The closest I found was the # PS1400300303 which is 11 inches to the center of the bracket when retracted as is # TJBB-2001-B.
  view full answer...
  
• Replacement Tongue Jack for 2002 Triton LT Snowmobile Trailer
  We don't have any offset jacks like the one you have on your 2002 Triton Trailer. I recommend going with the etrailer Round, Snap-Ring Swivel Jack # TJBB-2001-B as this jack will be more convenient as you will not have to reach down as far. This jack includes a welded footplate.
  view full answer...
• What Mounting Bracket Is Needed for the Round Snap Ring Swivel Jack TJB-2001-Z
  There is only one bracket needed to install the Round Snap Ring Swivel Jack part # TJB-2001-Z on your utility trailer and the bracket is included with the jack so no additional purchases are necessary. I have pointed this bracket out for you. It will need to be welded to the trailer frame. If you don't want to do any welding on the trailer then you can use the Round Snap Ring Swivel Jack w/ Footplate part # TJBB-2001-B instead which is essentially just a bolt-on version of the above jack...
  view full answer...
  
• Mounting Bracket Hole Spacing on etrailer Round Snap Ring Swivel Jack TJBB-2001-B
  The etrailer Round Snap Ring Swivel Jack # TJBB-2001-B has several mounting options thanks to the multiple holes in the included bracket. This jack bolts on to trailer frames up to 3-inches wide and from 2 to 4-inches tall. I went to our warehouse to measure the bracket mounting hole spacing for you and it is shown on the photo I linked.
  view full answer...
  
• Need Dimensions Of Round Snap Ring Swivel Jack TJBB-2001-B
  Hello Dennae, thanks for reaching out. I can definitely shed more light on the dimensions of the # TJBB-2001-B jack, but we don't have a CAD drawing we can send. Only the manufacturer would have that and they generally do not share those with the general public. The extended and retracted height we list is measured from the center of the swivel ring hole. So with the jack retracted, it measures 11" tall from the center of the hole to the bottom of the foot. Then with the jack extended...
  view full answer...
• Recommended Side Frame Trailer Jack for 3 x 3 Straight Tongue Trailer
  Based on everything you mentioned, the trailer jack I highly recommend for your trailer is the Round Snap Ring Swivel Jack with Footplate - Bolt On # TJBB-2001-B. This will easily bolt on to your 3" x 3" trailer tongue, has a 21-1/2" extended height which is perfect for the height of your trailer, and has a 2,000 lb capacity, which is more than enough for the weight of your trailer because a jack only needs to support the tongue weight of a trailer. This is a very high-quality jack with...
  view full answer...
  
• Recommended Marine Trailer Jack w/ a Wheel
  I do have a jack for you but the etrailer Item # TJBB-2001-B you were looking at does not have the option to add a wheel. Instead you will want the Pro Series Snap-Ring Swivel Marine Jack item # PSEJ10000101. This jack is similar to the Fulton F141005014 you referenced that is no longer active. It is a side wind jack, with a wheel, that has a 1,000 lbs capacity. It has a small foot print for the mounting bracket. I have linked a diagram below that will show the dimensions.
  view full answer...
  
• Recommended Bolt-On Swivel Jack for 5K Food Trailer
  I recommend using the 2K Round Snap Ring Swivel Jack w/ Footplate # TJBB-2001-B OR the 1,500 lb Round Swivel Marine Jack # MJ-1500B if you'd like a jack with a wheel. Both of these are cost-effective options that are still quality products. The 2K jack has an extended height of 21-1/2" while the jack with a wheel has an extended height of 24". Every bumper pull trailer should have a tongue weight that is no less than 10% or no more than 15% of the weight of the trailer. Since your 5K trailer...
  view full answer...
  
• How to Pick Out a Trailer Jack for a Boat Trailer
  The best way to pick out a jack is to pick out one that has enough capacity to handle the tongue weight of your trailer. Typically, tongue weight is 10-15 percent of the total weight of the trailer. So lets say your boat and trailer weight a total of 10,000 lbs. Most likely you would have a tongue weight of 1,000-1,500 lbs. Without knowing your tongue weight but knowing the weight of your boat I recommend you take a look at a 2,000 lb jack like the etrailer Round Snap Ring Swivel Jack...
  view full answer...
• Fit of etrailer Snap-Ring Swivel Jack on 2 x 3 Inch Trailer Frame
  The etrailer # TJBB-2001-B Snap-Ring Swivel Jack you referred to will fit trailer frames up to 3x4 inches. It'll fit your 2x3 trailer frame just fine as the mounting brackets have a series of holes that allow them to fit trailer frames of various heights.
  view full answer...
• Measurements of etrailer 2K Snap-Ring Swivel Trailer Jack
  I went out to the warehouse and pulled an etrailer trailer jack # TJBB-2001-B. From the center of the mount to the bottom when retracted is approximately 11 inches.
  view full answer...
  
• Availability of Bolt-On Pipe Mount Trailer Jack with 10" Lift
  All of our pipe mount trailer jacks do require welding, but we do have bolt-on jacks like the etrailer # TJBB-2001-B that should work. I was able to see that Kendon motorcycle trailers tend to have smaller frames and this jack is compatible with 2" - 4" tall frames that are no wider than 3". If your trailer frame is smaller than that please let me know and I can see if we have any other options available.
  view full answer...
• Recommended Replacement Tongue Jack For Additional Ground Clearance On Angle Iron Trailer Frame
  For the etrailer Round, Snap-Ring Swivel Jack #TJBB-2001-B to fit properly on your homemade camping trailer the frame will need to be boxed. This would require having additional frame material welded where you intend to mount the new jack. I recommend installing the Ultimate Trailer Jack # 322-RDJ-2K in your A-frame mount. This jack assembly can be raised to 1-3/4" with the jack retracted and moved to its lowest setting. The jack can then be adjusted in 2" increments up to 12" and raised...
  view full answer...
• Hole Spacing of Round Snap Ring Swivel Jack with Footplate TJBB-2001-B
  The Round Snap Ring Swivel Jack with Footplate part # TJBB-2001-B is a bolt-on jack, it fits a trailer frame between 2-4" tall. It does not install into any holes on the trailer frame. It come with new brackets and everything else you need to use the jack. That said, the hole spacing is attached below.
  view full answer...
  
• Recommended Tongue Jack for a 1997 Starcraft Space Flyer
  I was not able to pull up much information on a 1997 Starcraft Space Flyer but it looks like you might be looking for a side mount trailer jack. For this, we have a few options but I like Round Snap Ring Swivel Jack w/ Footplate part # TJBB-2001-B. This jack offers bolt-on instillation, a swivel mount design for improved ground clearance, and a wide-base footplate to prevent sinking on soft ground. I have attached a review video for you as well.
  view full answer...
• Overall Height of 2K Topwind Swivel Jack # TJBB-2001-B When Fully Retracted
  I measured this jack, Item # TJBB-2001-B, in our warehouse. It measures 15-3/4 inches from the footplate to the top of the outer tube. It measures 17-1/2 inches from the footplate to the top of the jack when the handle is folded in. I've attached an image showing these measurements.
  view full answer...
  
• Mounting Hole Dimensions for Round Snap Ring Swivel Jack 2K
  The Round Snap Ring Swivel Jack part # TJBB-2001-B will accommodate any trailer with frame 2" to 4" tall and up to 3" wide. That said, I have attached for you below the mounting hole dimensions as well.
  view full answer...
  
• Swivel Jack with Sturdy Pull Pin To Eliminate Jack Movement While Winding and Unwinding
  I'll start off by saying that part of the play that you're experiencing has a bit to do with the bolt on feature vs. a welded on jack; bolted on jacks are going to have a bit more play on them, but there are some features in jacks that you can look for that will lessen the play/wiggle you're experiencing. First, choosing a top wind jack over a side wind jack will help reduce some of the movement when you're winding/unwinding. Second, a strong pull pin that locks the jack into position...
  view full answer...
• Bolt-On Swivel Jack For Improved Ground Clearance
  You are correct that welding steel to aluminum is a tricky process best left to experienced welders, but if your issue is that you jack sometimes scrapes on the ground you can avoid the need to weld by simply bolting on a swivel jack. Pull Pin Swivel Jack # TJBB-2001-B has a 2000-lb rating, includes a foot plate and bolts on to the side of trailer frames up to 3-inches wide and from 2 to 4 inches tall. Just pull the pin to swivel the jack up and out of your way for travel. This jack extends...
  view full answer...
  

Do you have a question about this Trailer Jack?