Replacement For Venture/ADTH Landing Gear Motor & Gear Box

Question

Question:

looking for landing gear motor says on it adth e226168 landing gear box says nmc940rb023814

asked by: Tara G

0

Expert Reply:

That is a Venture/ADTH motor and gear box, and what you use to replace it is a motor and gear box from Stromberg Carlson, which are the following part numbers:

- Replacement Motor # LG-142178

- Replacement Aluminum Gearbox # LG-179015

expert reply by: Kyle S

0

Answer 1

Thanks for the picture! We sure do! You will want the Replacement Motor for Stromberg Carlson Electric Landing Gear item #LG-142178.

view full answer...

Answer 2

If the brand of landing gear you have now on your Keystone Laredo is a Ram brand then yes you could reuse it's motor with the #RVLG-8HDL. But most likely you have a Lippert set of landing gear based on what typically they used so instead the part…

view full answer...

Answer 3

If the bevel gears/gearbox for the dual-motor landing gear on your 2011 Keystone Laredo 266RL 5th wheel were badly worn or damaged you would most likely be able to hear it. These conditions typically cause a good bit of noise as the jacks try to…

view full answer...

Answer 4

Based on your description it sounds like you need a replacement motor for your landing gear. The correct replacement for your 1RV-200 is the #LC142178. If you need a replacement gear box as well then you can use the #LC276602.

view full answer...

Answer 5

Good question Mel, and I don't blame you for being confused since there are a lot of options and there is probably more than one right answer. The correct pivot arm position will depend on the clearance between the nose of the camper and the cab…

view full answer...

Answer 6

For your 2008 Keystone Everest, I recommend the Lippert Components HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 or the high speed #LC141893 along with the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear…

view full answer...

Answer 7

Hey Jay, thanks for reaching out! What landing gear do you have? The Lippert Venture Follow Leg Repair Kit #LC146060 is designed for LCI Power Landing Gear assemblies so if you have something different then that would explain why this isn't…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

When installing the pivot arms on your B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package - Dual Jaw - 25,000lbs Item #BWRVK3600 you'll want to ensure that you have 6" of clearance between the bed rails and the nose of your…

view full answer...

Answer 10

We sure do Billy! That 241846 part number you gave me corresponds to the Replacement Heavy Duty Driver Leg for Lippert Ground Control 2.0 Landing Gear item #LC241846. The item #LC241846 is intended to replace the heavy duty master leg on Lippert…

view full answer...

Answer 11

For the driver leg part #LC241846 that you have the correct repair kit you'll want is the #LC146059.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement For Venture/ADTH Landing Gear Motor & Gear Box

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching