Replacement Hardware Kit for Curt Hitch C15703

Question

Question:

I need a complete hardware kit for C15703 hitch. I had the hitch sand blasted and powder coated and everything else was lost in the process. Can you help? Thanks

asked by: Jason B

0

Expert Reply:

We sell replacement hardware kits for all of the hitches we offer including the Curt # C15703 that you referenced with the part # RHK.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 5

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 6

Hello Mel, great question! Yes, the Torklift tie downs part #TL66FV will fit your 2006 GMC Sierra 2500HD crew cab with the 8 foot bed, provided your truck does not have running boards or cab length boards that extend under the bed, and you are not…

view full answer...

Answer 7

Hey Steve, happy to help! The Victron MultiPlus II #VN43VR you're looking at can replace many of the functions of your Magnum MS2812, but there's an important difference with the AC connections. The #VN43VR has one AC input and two AC…

view full answer...

Answer 8

Hello Mike, thanks for reaching out. We do offer a few different hitches for the 2026 Subaru Crosstrek, the Curt #C22MJ, the Draw-Tite #76209 and the EcoHitch #EH57CR. All 3 of these hitches place the receiver in virtually the same position beneath…

view full answer...

Answer 9

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 10

Good morning to you as well Steve, and congrats on your new van! I would be more than happy to make a recommendation for you! The best hitch for your 2026 Toyota Sienna, is going to be our etrailer item #e56RR. This is a class III hitch with a…

view full answer...

Answer 11

Hi John! We definitely have hitches available for your 2026 Lexus RX350h and the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e29ZV is a great option. The matte finish makes our hitches blend in better than…

view full answer...

Answer 12

Thanks for supporting a local business Christopher! So long as your 2012 Chevrolet Silverado is a 1500 and you need a class IV hitch, the Curt item #14301 is going to be the best option. It has a 2" receiver with a 10,000 lbs towing capacity and…

view full answer...

Replacement Hardware Kit for Curt Hitch C15703

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching