Parts Needed For Connecting Truck Topper 3RD Brake Light Through 4-Way Trailer Connector

Question

Question:

Any way to connect topper 3rd brake light to 4 way flat plug on 2018 Ford 150 extended cab?

asked by: Tim M

0

Expert Reply:

Yes, you can connect a 3rd Brake Light Logic Module # PP20-702 to a 4-Way Flat Trailer Connector # HM48110. This will filter our the turn signals from the brake lights on your trailer connector. Then you will only need to run the power and ground wire up to your 3rd brake light on your topper.

expert reply by: Bud M

0

Answer 1

Hello Jean-Marc; to connect the third brake light you can use the 3rd Brake Light Logic Module #PP20-702. You will tap into the left and right brake/turn signal wires and run that up to your third brake light. The module will filter out the turn…

view full answer...

Answer 2

What you would want is the part #PP20-702 which you can wire to your trailer wiring 4-way to give you a dedicated stoplight circuit for your cap. The trailer wiring has the turn signals and stoplights wired on the same circuit which is why you would…

view full answer...

Answer 3

Hey Geroge! You can use the Curt T-Connector Vehicle Wiring Harness #C59DR, but you'll also need an adapter that separates out the stop signal from your turn signals. The 3rd Brake Light Logic Module #PP20-702 is a great tool to use for this, but…

view full answer...

Answer 4

It sounds like it's possible that the brake light wire from your 3rd brake light might be coming into contact with the electric brake wire on the trailer. The brake controller on your truck will send an intermentent, extremely small amount of…

view full answer...

Answer 5

Yes, you can use the factory trailer connector on your 2015 Nissan Titan to power the third brake light on your Leer camper shell. That said, they don't make a plug and play harness for this so you will need to do some wiring but no splicing into…

view full answer...

Answer 6

What I recommend doing is adding a second socket but by using the Curt T-Connector Vehicle Wiring Harness #C55384 instead of a hardwire option. This will tee in behind your 4-Way/7-Way so all of the functions will pass through but then you'll…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Parts Needed For Connecting Truck Topper 3RD Brake Light Through 4-Way Trailer Connector

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching