Connecting 3rd Brake Light on 2026 Ford Maverick With Snug Cap
Updated 10/05/2026 | Published 03/11/2026
Question:
Hi, I transfered my 2022 ford maverick snug cap to my new 2026 maverick hybrid and want to connect the third brake light, what will I need ? Any help woub be greatly appreciated.
asked by: Jean-Marc T
Expert Reply:
Hello Jean-Marc; to connect the third brake light you can use the 3rd Brake Light Logic Module # PP20-702. You will tap into the left and right brake/turn signal wires and run that up to your third brake light. The module will filter out the turn signal so only the brake light will come on on the truck cap.
(click to enlarge)
Bill
3/15/2026
Worked as described. I used it on a teardrop trailer I was building. Easy to use. I liked it enough to use again on another trailer.
Brad
3/15/2026
The module works as expected.
Jason
10/5/2026
What color wires on the truck do you tap into on the left and right brake lights with this module?
Robin H.
10/5/2026
Product Page this Question was Asked From
Featured Help Information
Instructions
Continue Researching
- Shop: 3rd Brake Light Logic Module
- Shop: Trailer Wiring
- Video: Setting Up the Roadmaster Stop Light Switch Kit - 2025 Ford Maverick
- Video: Roadmaster InvisiBrake Flat Tow Brake System Install Guide - 2025 Ford Maverick
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Complete Breakdown of the 3rd Brake Light Logic Module
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: tekonsha 90195 p3
- Search Results: wire
- Q&A: Replacement Klauber Slide Out Motor A-300 K01336A300 for RV
- Q&A: Gate Valve Mounting Bolt Spacing for Valterra T40A Bladex Waste Valve
- Q&A: How to Sync the Lippert Remote Part # LC358601 to the Multi-Function Pad
- Q&A: Replacement Motor for Klauber Slide Out Motor K01431B300
- Search Results: 80960
- Search Results: 180455
- Search Results: 51126
- Q&A: Soft Start Recommendation for 13K Bu Furrion Chill HE AC Unit
- Search Results: wheel simulator
- Search Results: ss401
- Q&A: Looking For Replacement Door For B and B Water Center
- Q&A: Solution For 2023 Ford Maverick For Third Brake Light Wiring for Camper Shell
- Shop: Safe-T-Plus Steering Stabilizer
- Shop: Truck Topper
- Shop: SumoSprings Maxim Custom Helper Springs - Rear Axle
- Video: Checking Out the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector-C59DR
- Video: How to install the Curt T-Connector Vehicle Wiring Harness on a 2023 Ford Maverick
- Shop: etrailer 12V Power RV Patio Awning - 10' Wide - 8' Projection - 4-Layer Vinyl - Black Fade
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: Vehicle Tow Bar Wiring
- Shop: Ladder Rack
Gc
3/15/2026
Hello Jean-Marc. I used this module on my new 2026 Ram 2500 Power Wagon and Overland AT Atlas Topper and it works great. Not sure how your truck is set up, but I located the module behind the driver side tail light, because that's the side the topper's 3rd brake light and other electrical accessories were made available. Locating it near one of the brake lights gives you easy access to one of the brake indicator wires, so you'll only have to run one wire over to the other light. You can ground the third wire to any good body/chassis part that you can confirm is grounded with multimeter. I drilled and cleaned a hole for ground on the steal panel behind the brake light housing and properly weatherproofed it. Just a note - before I installed the module and ran the wire, I tested it with long jumper wires to confirm operation. Good luck!