Inner Diameter of Solera Awning Rail Extrusion # LC715216

Question

Question:

Do you know what the inner diameter is of the channel on this rail?

asked by: Dave

1

Helpful Expert Reply:

The Solera Awning Rail Extrusion # LC715216 has an inner channel diameter of 11/32". The slot opening is 5/32" for the awing material to fit through.

expert reply by: Bud M

1

Solera Awning Rail Extrusion # LC715216 Channel and Opening Dimensions
(click to enlarge)

Answer 1

What you heard is correct, the 59-1/2" arm assembly you currently have is no longer available. The 63" arm is what you are looking for. You can either use the black #LC404523 or white #LC97UD replacement arms which will work for both sides.…

view full answer...

Answer 2

I reached out to my contact at Lippert with the measurement of your support arm and they confirmed that the Replacement Short Arm Assembly for RV Awnings #LC97UD you were looking at is the correct replacement support arm assembly for your 2021 Jayco…

view full answer...

Answer 3

The awning arms are measured from top to bottom of the wall mount. This can then be used to select the correct length replacement. I have attached a photo below to assist. You will also need to pay attention to the style of arms such as pitched or…

view full answer...

Answer 4

When your current pitch arm is folded out and fully extended measure it's overall length. If it's 69 inch it would be the part #LC375994 for a replacement or if it's 63 inches #LC97UD.

view full answer...

Answer 5

If I had to take a guess, I would say the batteries are dead. This is rather common when someone goes to get in their camper after it sits in the offseason for a few months. I know you said you have power to the lights but the lights only consume a…

view full answer...

Answer 6

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Inner Diameter of Solera Awning Rail Extrusion # LC715216

Product Page this Question was Asked From

Continue Researching