Thule Square Bar Roof Rack That Fits A 2022 Subaru Outback With Factory Raised Rails

Question

Question:

What Thule square bars will work with my 2022 Subaru Outback Wagon, non-wilderness. I have factory rails that run the length of the roof

asked by: Ken J

0

Expert Reply:

For your 2022 Subaru Outback Wagon, I recommend the Thule SquareBar Evo # TH712300, with the Evo Raised Rail Feet for Thule Crossbars # TH710401.

These bars have a maximum weight capacity of 220-lbs, and measure 47" long, 1-1/4" wide, and 7/8" tall.

I recommend checking your vehicle owners manual for the maximum weight capacity that your roof can hold, and use the lowest rated component between the roof rack, and your roof, to ensure you aren't going to overload your vehicle.

expert reply by: Bryce D

0

Tina

7/21/2025

I bought the Thule raised rail feet to go on my 2022 non-wilderness Outback so I could install my Hullivator, but the full length rails are not really rails at all-just cladding & places to store to retractable crossbars. Those feet did not work at all. (I bought them based on the Thule website fitting guide). Even if the raised rail feet could be mounted in the available rail opening, you'd have about 15" to work with. Its honestly a terrible Subie design that makes putting racks on almost impossible. I'm still looking for the right feet to mount my hullivator on. The feet must attach to the crossbars.

Nick S.

7/21/2025

@Tina I am sorry to hear about the first try, getting those to install. From what I could find looking at options for your vehicle the feet and fit kit for your 2022 Non-Wilderness Outback are parts # TH710601 and # TH37CE. Both of those used together would be able to allow you to attach the crossbars to your vehicle, and then the Hullavator onto your crossbars. Those 2 parts are the same part in any of our Thule racks for your vehicle.

Tina

7/21/2025

@NickS I will check those parts out. Thank you! Its expensive to buy the wrong thing & have to start over. Fingers crossed!

Nick S.

7/21/2025

@Tina I totally understand that! My online shopping luck is never the greatest haha. Those feet and that fit kit should get you all set and ready to go. You'll have to let me know how the install goes for you this time around.

Answer 1

I really like the Air Lift WirelessAIR Suspension System for Air Helper Springs Kit #AL27DQ for your 2024 Chevy Silverado 3500 because it comes with an EZ Mount system for easier compressor installation on your truck, and then the kit also comes with…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Thule Square Bar Roof Rack That Fits A 2022 Subaru Outback With Factory Raised Rails

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching