Replacement 22210 Spring Bars for Reese Trunnion Weight Distribution System

Question

Question:

I’m looking for a replacement bar 22210 for my Reese hitch

asked by: Jeff

0

Expert Reply:

The 22210 part number you provided is actually the part number for the trunnion end which Reese no longer offers separately. But the replacement 800 lb spring bar IS available as part # RP22225. A hardware kit is also available as part # 66014.

expert reply by: Mike L

0

Replacement 800 lb Reese Trunnion Style Spring Bars
(click to enlarge)

Answer 1

Hey Robin! I'm sorry to say that none of the Advent Air AC models are able to replace a Dometic Duo Therm like yours. What I recommend is completely replacing the system. Not only will this allow you to avoid any compatibility issues, it will…

view full answer...

Answer 2

I spoke with Lippert about the mounting brackets for the Lippert On-The-Go Telescopic Ladder #LC64HD and found out that they are only sold as an OEM part. This means that only the motorhome/trailer manufacturer is able to order them so you…

view full answer...

Answer 3

I do have a possible solution for you but unfortunately there aren't any battery boxes available that will hold two 12V batteries and fit within a 21" length and 8" width. The closest thing we have is the TorkLift PowerArmor Locking…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement 22210 Spring Bars for Reese Trunnion Weight Distribution System

Featured Help Information

Miscellaneous Media

Continue Researching