Could Trailer Valet JX Trailer Jack TV94FR be Used on 3,900 lb Trailer

Question

Question:

Will the Trailer Valet JXC Sidewind 5K work for my 23 foot Airstream trailer that weighs +- 3900 lbs?

asked by: Edd Q

0

Expert Reply:

Yes, the Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option # TV94FR that you referenced would work great on your 23 foot Airstream trailer that weighs 3,900 lbs. Since this has quite a bit more capacity than you'd need it would be very easy to crank.

expert reply by: Jameson C

0

Answer 1

To verify that the Trailer Valet JXC Trailer Jack #TV54FR will fit your 2018 Nucamp Tab400 you will need to verify that the opening for the a-frame jack on your Tab has at least a 2-1/4" opening. The JX2#TV54FR is enough for your Tab as the…

view full answer...

Answer 2

The Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option #TV94FR is made in China. If you are looking for a manual jack with 5,000lb rated capacity that is made in the USA we have the A-Frame Trailer Jack by Dutton-Lainson #DL22772.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Could Trailer Valet JX Trailer Jack TV94FR be Used on 3,900 lb Trailer

Product Page this Question was Asked From

Continue Researching