Can a Cattle Trailer With 7,000Lb Torsion Axles Be Converted To Leaf Sprung Axles?

Question

Question:

Does this hanger kit work on a cattle trailer with 2 torsion axles 7k each

asked by: Juan L

0

Expert Reply:

The Tandem-Axle Trailer Hanger Kit for Double-Eye Springs # APT8 can be used on your cattle trailer if you are changing from torsion springs to leaf spring axles.

I can help you find the correct axles, hubs, brakes, leaf springs and any additional components you will need if you can provide me the frame measurements, axle hub face spread, wheel spacing front to rear. I have linked a help article below that will help cover all the parts that will be needed.

expert reply by: Bud M

0

Answer 1

I do have a few options available for you however, we currently do not sell torsion axles. You have two options to consider for your trailer, the Timbren axle-less suspension and the Dexter straight axles. As you have a gross trailer weight (GTW) of…

view full answer...

Answer 2

Hey Sandy, Inside wear on the tires is definitely an indication of a loss of camber. That along with what I think you're referring to as a decrease in wheel well clearance tells me that it's probably indeed time to replace those Torflex…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...