What Size Bolts Come with the Curt Trailer Hitch Receiver 13091

Question

Question:

do mounting bolts come with the curt 13091 and if so what size are they

asked by: Ralph H

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 13091 comes with four M12x1.25 hex bolts and four 1/2" conical tooth washers.

expert reply by: Conner L

0

Answer 1

I do have an option for you, however the Buyers Products Receiver Tube #3371804055 that you referenced will not line up with the existing holes on your Mitsubishi Montero's frame behind the bumper. For a 2 inch hitch receiver that is confirmed to…

view full answer...

Answer 2

I do have a trailer hitch for your 1990 Mitsubishi Montero, but I spoke with my contact at Curt and he confirmed that the Curt Class III Trailer Hitch, #13091, was designed to fit only the 1992 to 2000 Mitsubishi Montero except the sport model. The…

view full answer...

Answer 3

Curt lists the #13091 as a fit for the 1992-2000 Mitsubishi Montero but not the 1991 Land Cruiser. They do however list the the #C12181 as being a fit for both the Montero and the 1991 Land Cruiser, so obviously the bolt pattern is identical. Since…

view full answer...

Answer 4

The closest option we have to the 3-1/2" x 2" bolt pattern you mentioned that your 1989 Land Rover Defender bumper has is the Curt #13018 which has a mounting hole pattern that measures 2-1/4" x 3-1/4" as shown in the included…

view full answer...

Answer 5

You are correct. The Curt hitch part #13091 that you referenced is rated for towing up to 4,000 lbs. Because of that you would be limited to only towing that even if your vehicle is rated to tow more. In a towing setup your overall towing capacity is…

view full answer...

Answer 6

The only hitch we offer for your 1990 Mitsubishi Montero is the Curt hitch part #13091 which has a 1-1/4 inch opening. The only way to use a 2 inch hitch accessory with this hitch would be to use the hitch adapter part #HTAD. Only thing about hitch…

view full answer...

Answer 7

I spoke with my contact at Curt about trailer hitch #13091. The hitch is designed to fit a 1992 to 2000 Mitsubishi Montero 2 or 4 door (but not Sport models), so if it is being installed on one of those specific vehicles, it cannot be used upside…

view full answer...

Answer 8

The distance between the holes is 3-3/8 inch and 1-3/4 inch. The only hitch we have for your 1991 Mitsubishi Montero is the Curt part #C12181 which is a Class II hitch with a 1-1/4 inch opening. The 2 inch hitch size is only used on higher capacity…

view full answer...

Answer 9

The 10 amp fuse that is included with the Curt T-Connector Vehicle Wiring Harness part #C56217 will need to be the one that you insert into the #29 slot. The owner's manual does indeed call for a 30 amp fuse here but that is with the factory…

view full answer...

Answer 10

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...