Distance from Hitch Pin Center to Ball Center of Blue Ox TrackPro Weight Distribution

Question

Question:

What is the distance from the hitch pin to the center of the ball mount?

asked by: Nate J

1

Helpful Expert Reply:

I checked with Blue Ox and they told me that the Blue Ox TrackPro weight distribution # BLU36FR has a distance of 14.39 inches from the center of its hitch pin hole to the center of the hitch ball.

expert reply by: Jameson C

1

Pin Hole to Ball Center Dimension TrackPro
(click to enlarge)

Answer 1

Hey Mike, welcome back! The 2-1/2" shanks have the same channel size as the 2" shank for the Andersen Weight Distribution Hitch so they all work for the same system. We didn't have the 2-1/2" shanks available separately so I went…

view full answer...

Answer 2

Hi Jason! I have a diagram attached that shows all the measurements you are requesting. It's a little rough (I'm definitely not an artist), but it should have everything you are needing. If I missed anything, just let me know and I can get…

view full answer...

Answer 3

Hey Pat, the Snap Pad part #SN97FR is sold individually. We have options where they are sold in sets though so if you needed a set of more just let me know and I'll see what you'd need. For example, we have a set of 4 with the part #SN27FR.…

view full answer...

Answer 4

Hey Jeff! The B&W Continuum #BW28FR, and other weight distribution systems, do not add to the tongue weight of your setup. It becomes part of the hitch and frame of the vehicle so you don't have to worry about the weight of the system pushing…

view full answer...

Answer 5

Hey Ray, while there certainly is a lot of appeal to the Andersen WD systems like the part #AN88VR what we have found is that if the tongue weight is more than a few hundred lbs they just don't work as well as the traditional systems that use…

view full answer...

Answer 6

Hey Mark! The B&W Continuum #BW78FR is great for any setup as long as you're in the 600–1,600 lb tongue weight range of the system. The best part about it is you can set it perfectly for any tongue weight so it won't be over or…

view full answer...

Answer 7

Hey Jon, I have a solution for you but I would not recommend the Andersen Weight Distribution system part #AN33VR for your 2025 Brinkley Z Air 297. What we have found is that the Andersen system does a decent job with lighter weight trailers but for…

view full answer...

Answer 8

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 9

Hey Frank. I can give you the dimensions of the shank on the B&W Continuum item #BW28FR but you're going to need to take the measurements on your Silverado 3500 to confirm the tailgate will open. From the hitch pin hole to the center of the…

view full answer...

Answer 10

Hey Stuart, unfortunately weight distribution systems do make some odd noises. Friction does a great job as a way to reduce sway but it does make a lot of noise. So with that said the friction in a weight distribution system is not intended to be…

view full answer...

Answer 11

Good morning Hurley (cool name by the way. I like the clothing brand Hurley). Also, congrats on the new-to-you Chevy! That is an excellent question that comes up from time to time on various vehicles and weight distribution systems. So on your 2023…

view full answer...

Answer 12

On the shank of the Blue Ox weight distribution system part #BLU36FR that you referenced the distance between the hitch pin hole center and the adjustment hole centers is 9 inches.

view full answer...

Distance from Hitch Pin Center to Ball Center of Blue Ox TrackPro Weight Distribution

Product Page this Question was Asked From

Continue Researching