Is There A SolidStep Manual Fold Down Step That Will Fit My 25-1/4 Wide Doorway

Question

Question:

What are the dimensions of these steps?

asked by: Dave M

0

Expert Reply:

The SolidStep Manual Fold-Down Steps for 25" - 28-7/8" Wide RV Door Frames - Double - Aluminum, part # LC733931, will fit your RV door without any issues. These steps will fit doorways from 25" wide up to 28-7/8". The 1/4" difference will not cause problems with the fit.

I have attached a video review link below.

expert reply by: Mark Smith

0

Dave M.

1/14/2022

What are the dimensions of these steps?

Mark S.

1/14/2022

The dimensions of the SolidStep Manual Fold-Dowon Steps, part # LC733931, are as follows: Entry height: 22" - 28" Doorway width: 25" - 28-7/8" Bracket width range: 23" - 31-13/16" Step dimensions: 20" wide x 8-1/2" deep Top step depth: 13" deep Drop/Rise: 8" I do understand your concern about the steps being a tight fit for your doorway -- the steps measure 25", while your doorway measures 25-1/4", but these steps will still fit in the fold-up position. However, I do have another option for you if you have not been swayed. If you go with the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 2 Steps, part # MR26RR, you will get a step that will meet your entry height and your doorway width requirements. The steps can be adjusted in 1" increments. If you adjust them to 24-3/4", they will fit your doorway and provide you will some breathing room when they are in the stored position. I have included a product description link and a video review link below.

Answer 1

Hello Ed, thanks for reaching out. The MORryde StepAbove RV Steps #MR26RR are designed to work with an entry height between 25" and 29". With only 22" between the threshold and the ground the step would not have enough room to open all…

view full answer...

Answer 2

Hey Chris. I don't have a database that shows me what parts came with your Forest River R-Pod RP-189 so I'll need you to take a couple quick measurements to get you the right replacement steps. To find the correct replacement, you'll need…

view full answer...

Answer 3

The Lippert SolidSteps part #LC713662 that you referenced look like the picture that I attached.

view full answer...

Answer 4

Some weight distribution system prohibit reversing because doing so could damage the system. If you are backing up in a straight line though it would be fine. But to make turns while backing up you would need to disengage the spring bars and/or the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Is There A SolidStep Manual Fold Down Step That Will Fit My 25-1/4 Wide Doorway

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching