How Does an EZ-Lube Axle Work

Question

Question:

how does the greese get to the inner brg the boring seems to end at the cotter pin and the gesse comes out there to greese the outer brg. I just ordered buddy brgs to see if the greese will get to the inner brg

asked by: Al L

0

Expert Reply:

On an EZ-Lube axle, the grease gets inserted at the end of the spindle through a zerk fitting and comes out of a hole that should be in between the bearings, filling them both. You would not be able to use Bearing Buddies because the zerk fitting at the end of an EZ Lube axle would interfere with the installation.

expert reply by: Michael H

0

Answer 1

We sure can! The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 2

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 3

Thank you for the pictures. Your Timbren 3500 Axle-Less system has the upgraded heavy duty spindle. This will use the Bearing Kit #BK3-100. This will include the following components if you do not want the entire kit. Inner Bearing #25580 Inner Race…

view full answer...

Answer 4

With the 1/2 inch diameter wheel studs on your etrailer.com Idler Hub Assemblies #AKIHUB-545-35-K and the 15 inch steel wheels from the Loadstar Tire and Wheel #AM3S640DX, you are looking at a torque spec of 90-120 ft.-lbs for the lug nuts. I have…

view full answer...

Answer 5

The center portion of the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 is designed to allow the grease to expand slightly when warm and not pop the cap off. If you are seeing it pop out when cold you may have too much grease in the hub. I'd…

view full answer...

Answer 6

In order to remove the hub/drum on your trailer you will want to first remove the spindle nut. Once the spindle nut is removed you are going to want to take a hammer and tap the outer portion of the drum as well as the hub face a few times to break…

view full answer...

Answer 7

The hub you describe is a 3500 lb 10 inch hub/drum with a 6 on 5-1/2 inch bolt pattern which uses an L44649 outer and an L68149 inner wheel bearing and a 58846 grease seal. For a replacement, I'd recommend the #AKHD-655-35-EZ-K hub/drum. The…

view full answer...

Answer 8

I spoke to Lock N Roll and they use 6mm x 1 low profile zerk fittings in their Articulating Coupler #336TS504. The low profile ones can be a little difficult to locate, but they are out there. We do have the Marlboro Replacement Brass Grease Zerk - 6…

view full answer...

Answer 9

The zerk fittings on the Dexter Trailer Axle #T3584F-EZ-8974 are a 1/4" pipe thread. If you need a replacement zerk fitting you can use part #Gzerk, which we have confirmed to fit the Dexter Ez-Lube Axles.

view full answer...

Answer 10

Thanks for the photo, and you are correct, you do indeed have a Dexter 7,000 lb axle, and are also correct regarding the shoes and magnets for Dexter 7k electric brakes, the Replacement Shoe #DX28FR and Replacement Magnet #BP01-225. That said,…

view full answer...

Answer 11

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb axles…

view full answer...

Answer 12

I really suggest you just take the trailer back to the dealer and have them fix the issue because the second you try to fix their mistake, the warranty for the work they performed goes out the window. That said, if the brakes are humming then that…

view full answer...

How Does an EZ-Lube Axle Work

Product Page this Question was Asked From

Continue Researching