Should Center Plug of Grease Cap Plug E-Z Lube Grease Caps # RG04-010 be Pushed Out All the Time

Question

Question:

Should the rubber nipple on the grease plug be pushed in, or is it suppose to be extended out...does it matter? When I push it in, it pops back out.

asked by: Garnett

1

Helpful Expert Reply:

The center portion of the Grease Cap Plug for E-Z Lube Grease Caps # RG04-010 is designed to allow the grease to expand slightly when warm and not pop the cap off. If you are seeing it pop out when cold you may have too much grease in the hub. I'd probably take the cap off to inspect.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 2

We sure can! The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 3

On an EZ-Lube axle, the grease gets inserted at the end of the spindle through a zerk fitting and comes out of a hole that should be in between the bearings, filling them both. You would not be able to use Bearing Buddies because the zerk fitting at…

view full answer...

Answer 4

Thanks for the photo, and you are correct, you do indeed have a Dexter 7,000 lb axle, and are also correct regarding the shoes and magnets for Dexter 7k electric brakes, the Replacement Shoe #DX28FR and Replacement Magnet #BP01-225. That said,…

view full answer...

Answer 5

I really suggest you just take the trailer back to the dealer and have them fix the issue because the second you try to fix their mistake, the warranty for the work they performed goes out the window. That said, if the brakes are humming then that…

view full answer...

Answer 6

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb axles…

view full answer...

Answer 7

Yes, 7k trailer axle brake assemblies like #23-180-181 will fit 6k axle hub/drums. They use the exact same dimensions and bolt patterns which allows that. The difference is the strength or sensitivity of the magnets in the assemblies. The 7k axles…

view full answer...

Answer 8

The grease cap you need is part #21-42-1. The rubber plug that you would then need is the part #RG04-010. We are going to need to know the width of your current grease cap on the other trailer to pick out a Bearing Buddy. Or you can measure the inner…

view full answer...

Answer 9

I recommend using the CE Smith Trailer Idler Hub Assembly #CE13515 for your Calkins boat trailer. These have the 5 on 4-1/2" bolt pattern and is prepacked and greased for your spindle. You can add the Bearing Buddy Bearing Protectors #BB1980A-SS…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Should Center Plug of Grease Cap Plug E-Z Lube Grease Caps # RG04-010 be Pushed Out All the Time

Product Page this Question was Asked From

Continue Researching