Spring-Loaded Quick Pins for Landing Gear Leg of 2015 Heartland Elkridge E275

Question

Question:

I have a 2015 Heartland Elkridge E275 5th Wheel and would like to know what Quick Pins would fit my Landing Gear Legs. The pins that are currently on the 5th wheel just barely goes all the way thru the legs when set.

asked by: Steven I

0

Expert Reply:

Based on the picture of your landing gear it looks like you have Ram jacks on your 2015 Heartland Elkridge E275 which would mean the correct replacement quick pin kit would be the part # RVLG-SPP.

That said yours look like they could just be gunked up and if you hit them with a degreaser and a power washer you might be able to get them to free up enough to work again.

expert reply by: Jameson C

0

Landing Gear Jack Leeg with Quick Pin
(click to enlarge)

Answer 1

Hey Bob, you will be able to use/install the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 but you will have to move one mounting bracket to get closer to the correct distance. The old brackets would need to be cut off and then welded back…

view full answer...

Answer 2

I believe we may have what you are looking for, but to answer your question the Spring-Loaded Pull Pin for etrailer and Ram 5th Wheel Landing Gear #RVLG-SPP is designed for Landing Gear Set #RVLG-8000 which has a 2-1/2" square leg and a…

view full answer...

Answer 3

I checked the Spring Loaded Pull Pins #RVLG-SPP, #LG-119113 and #UF17-943031 that we have that are designed to replace those that are on your Lippert landing gear with the 3/8" pins and they all measured at 2-5/8" long from the mounting…

view full answer...

Answer 4

Yes, the Replacement Lead Leg #LC119102 is the correct leg for your VMC900R Venture Landing Gear on your 2009 Keystone Cougar 5th wheel. The Replacement Follow Leg #LC119101 is also available if you would like to replace the follow leg as well on…

view full answer...

Answer 5

For the leg of your Trails West Gooseneck Trailer, the Replacement Pin options depend on the diameter of your jack's pin. There are options that have chains or springs depending on that pin diameter. If you have a 5/8 inch pin diameter then…

view full answer...

Answer 6

I may have a solution for you, but I wasn't able to find any specs regarding your Atwood landing gear. With that said, the Spring-Loaded Pull Pin for etrailer and Ram 5th Wheel Landing Gear #RVLG-SPP is designed for Landing Gear Set #RVLG-8000…

view full answer...

Answer 7

We do have motors that you can add to your landing gear. For example, the Landing Gear Set #RVLG-8000 can be operated with the manual crank #RVLG-HDL but you can also add the motor #LC142178 and switch #LG-145236 for effortless operation on your end.…

view full answer...

Answer 8

If you take a look at the picture I have included you will see several measurements on a landing gear leg. If your existing landing gear jack legs match then it has the standard spacing so #RVLG-8000 with motor #LC142178 is a great option that…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Spring-Loaded Quick Pins for Landing Gear Leg of 2015 Heartland Elkridge E275

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching