Will Ultra Fab Landing Gear Fit if Mounting Brackets Don't Line Up
Updated 08/31/2026 | Published 08/21/2026
Question:
I am wanting to replace the front jacks that currently has one motor. I am looking at the Ultra-Fab Landing Gear - 17-943010. I measured the distance from the bottom of the bottom bracket to the bottom of the top bracket at 19.5. the document for the new jacks says 19.125. is this a no-go or will it be ok to install? thanks
asked by: BOB D
Expert Reply:
Hey Bob, you will be able to use/install the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 but you will have to move one mounting bracket to get closer to the correct distance. The old brackets would need to be cut off and then welded back on in place. What brand of landing gear do you have now?
Product Page this Question was Asked From
Ultra-Fab Deluxe Electric Landing Gear Set - Weld On - 38" Lift - 12,000 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 10001 lbs or More
- Electric Jack
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Rubber Compression Bumper for MORryde Pin Boxes
- Video: Replacement Rubber Compression Bumper for MORryde Pin Boxes Feature Review
- Shop: Spring-Loaded Pull Pin for etrailer and Ram 5th Wheel Landing Gear
- Search Results: camper jacks
- Shop: Spring-Loaded Pull Pins for Stromberg Carlson Landing Gear - Qty 2
- Q&A: Replacement Jack Foot Pin for Easy Removal on Trails West Gooseneck Horse Trailer
- Q&A: Replacement Landing Gear Legs For Venture Landing Gear VMC900R On a 2009 Keystone Cougar 5TH Wheel
- Q&A: Spring Loaded Pull Pin for Landing Gear With 2-14" Square Legs
- Q&A: Replacement Landing Gear Spring Loaded Pull Pins For Lippert 2-1/4" Landing Gear With 3/8" Pin
- Shop: Extended Length Spring-Loaded Pull Pin for etrailer and Ram 5th Wheel Landing Gear
- Shop: Replacement Swivel Pin Kit for Trailer Jacks
- Q&A: Landing Gear on Keystone Raptor Slips and Has Trouble Raising the Trailer
- Q&A: Comparing the Reese # RP500708 and Ultra-Fab Deluxe # UF17-943010 Landing Gear
- Q&A: How to Choose the Correct Replacement Landing Gear for 5th Wheel Trailer
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - Weld On - 38" Lift - 12,000 lbs
- Video: Checking Out the Ultra-Fab Deluxe Electric Landing Gear Set
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Shop: Brake Controller
- Video: How to Choose a Trailer Brake Controller
on Camper Jacks
Josh
8/28/2026
I purchased these and installed them on my 2010 keystone Outback. I had the same 19.5 measure ment from bottom of lower bracket to bottom of upper bracket and they fit perfect. My bracket measure ments are as follows -19-1/2in from bottom of lower bracket to bottom of upper bracket. -21-3/8in from bottom of lower bracket to top of upper bracket -17-5/8in from top of lower bracket to bottom of upper bracket The jack itself has a 24inch outer casing from the bottom outlet to the bottom of the motor plate. And has anti slide stops on that casing just incase something loosens up. they are 12-1/2 inches apart inside to inside and 14-1/2 outside to outside. Your camper brackets just need to outside of that and it should work great. Hopefully this helps Josh