Parts to Replace Hydraulic Brake System on a 2004 Magic Tilt Trailer
Published 05/17/2013
Products Featured in This Question
Question:
I am trying to get pricing to replace my entire hydraulic brake kit brakes, rotors, hoses, coupler for a 2004 Magic Tilt triple axle aluminum trailer. I believe the model number is TTALS3190. The GVWR/PNBV is 10260 LBS GAWR/PNBE 3420 LBS Each axle has has tires ST205/75D14 C Any help would be greatly appreciated. Thanks
asked by: Marx S
Expert Reply:
We can definitely get you started with parts for your Magic Tilt Trailer, but we will need some additional information to complete your parts list.
We can start with a coupler. Since your boat trailer will not exceed 10,260 lbs, I recommend looking at a coupler like the Titan Zinc-Plated Brake Actuator for Disc Brakes, # T4750620. This coupler has a 3 inch drop like the coupler you referenced, but it has a 12,500 lb weight capacity which is closer to the weight of your trailer. Using a coupler with a significantly higher weight capacity could result in poor braking. This coupler can be bolted onto a 3 inch wide channel tongue and also comes with a protective shield in case you add an electric lockout solenoid valve, # T4748800. The solenoid valve will allow you to back up your trailer without actuating the brakes.
If you do not need a coupler with a drop, then you could use the Titan Brake Actuator, # T4750800.
Next, you will need brake lines. For this, you can use the Tandem Axle Hydraulic Brake Line Kit, # 9579-2, with the Hydraulic Line Kit for a 3rd Axle, # 9579-01. These kits should provide plenty of brake line for all three axles.
The last part that you will need are the disc brakes. To determine which disc brakes will work best for you, we will need to know what type of disc brakes you are using or want to use. We offer hub/rotor assemblies or rotors that slide over your existing hubs.
If you want the hub/rotor assembly, I will need to know the part numbers of your bearings and grease seal. The part numbers will be stamped into the metal of the bearing and in the rubber of the grease seal. If you cannot find the part numbers of the bearings or grease seal, you can take some measurements of your spindle. I have attached a photo that shows where the part numbers can be found and where to measure on your spindle. Your spindle measurements must be exact, so I recommend using a precise measuring tool such as a dial caliper to take the measurements.
If you want the rotors that fit over an existing hub, I will need to know the bolt pattern of your existing hubs to ensure you get rotors that will fit.
I have attached an FAQ article on parts needed to add hydraulic disc brakes for you to check out.
Product Page this Question was Asked From
Dexter Zinc-Plated Brake Actuator w/ Drop - Drum - 2-5/16" Ball - Bolt On - 20,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Boat Trailer
- Construction Trailer
- Farm Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 20000 lbs GTW
- 2-5/16 Inch Ball Coupler
- 3 Inch Channel Tongue
- Drum Brakes
- No Lockout
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Zinc-Plated Brake Actuator w/ Drop - Drum - 2-5/16" Ball - Bolt On - 20,000 lbs
- Video: An In-Depth Look at the Dexter Zinc-Plated Brake Actuator w/ Drop
- Shop: Replacement Bearing Buddy Bras - Model 23B - Qty 2
- Shop: Dexter Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 38" Axle Spacing
- Shop: Demco Hydraulic Brake Actuator w/ Drop - Drum - Zinc - 2-5/16" Ball - 20,000 lbs
- Shop: Master Cylinder for Titan Model 10 and 20 Actuators - Drum Brakes
- Q&A: What is a Trailer Spring Seat
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer tires and wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Search Results: trailer brakes
- Shop: Gooseneck Hitch
- Article: How to Measure Your Trailer Wheel Bolt Pattern
on Brake Actuator
