Recommended Replacement Grease Seal for a 3109 Seal

Question

Question:

Hi customer service, I am looking 2 grease seals # 3109 5m for axle, if you carry please let me know, thanks.

asked by: Jose M

0

Expert Reply:

For your 3109 grease seals, you can use the Grease Seal # 1105-100-035 for replacements. This grease seal has the same measurements (2" I.D. | 2.875" O.D.) as your current seal and has a thickness of .3".

expert reply by: Bryce D

0

Answer 1

Though we do have the replacement bearings, races, and seals available for your Hadco 3109 hub (which I have listed below), the combination used will not have an equivalent replacement hub available, unfortunately. Replacement Trailer Hub Bearing…

view full answer...

Answer 2

The measurements from your spindle and hub line up with the HADCO seal #1105-100-035 that you were looking at. This will work as a replacement to your seal on your axle. Sounds like you were looking for a rubber coated one like the one that was…

view full answer...

Answer 3

After speaking to my contact at Redline, I have found the thickness of the Redline Grease Seal #1105-100-035 you referenced is .3 inches.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Replacement Grease Seal for a 3109 Seal

Product Page this Question was Asked From

Continue Researching