2018 Micro Mini with Lippert 3,500 Torsion Axles Lift Kit

Question

Question:

Looking at your site it shows the drexler lift is common with mounting holes 8” on center. Mine are 9” on center and the axle has a sticker that say lippert components 3500 lb. do you offer a lift for this setup?

asked by: Bryan F

1

Helpful Expert Reply:

Based on the info you listed the correct lift kit for your Lippert torsion 3,500 lb axle is the part # LC270682 which will give you a lift of 2-5/8 inches.

expert reply by: Jameson C

1

Answer 1

Hey Luke, the Torflex Lift Kit part #K71-707-02 is made from 7 gauge steel which is 3/16 inch thick. Are you curious for an alternate application?

view full answer...

Answer 2

For your 3,500 lb Dexter Torsion axles, you will want to use the Torflex Lift Kit - Tandem Axle - 2-5/8" Lift #K71-707-02. This will provide an additional 2-5/8" clearance. The distance between the mounting bolts is 8 inches center on…

view full answer...

Answer 3

Hey Mark, yes the Torflex lift kit part #K71-707-02 that you referenced would be the correct lift kit to use for your trailer. What you have is the #10 axle based on the capacity so this is correct fit and will give you a lift of 2-5/8 inches. Are…

view full answer...

Answer 4

Since the sticker on your trailer axle says Dexter Number 10 that means the lift kit part #K71-707-02 is a confirmed fit and would give you an additional 2-5/8 inches of lift. This is the biggest lift we offer for your trailer/axle setup. I attached…

view full answer...

Answer 5

Since you have a 5,200 lb Dexter Torflex tandem axle setup the correct lift kit is the part #K71-724-02. This will give you a 2-7/8 inch lift and would work well.

view full answer...

Answer 6

Thanks for the information! Since your torsion axles have 8" bolt hole centers you'll need the Torflex Lift Kit item #K71-707-02. These lifting blocks are for #10 torsion axles and will give you a 2-5/8" lift.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

2018 Micro Mini with Lippert 3,500 Torsion Axles Lift Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching