Correct Replacement Leaf Springs for Trailer with Dexter 3,500 Lb Axle

Question

Question:

I need replacement springs for 2016 Northwood Nash 23D 3500 lb. Dexter axel..

asked by: Scott L

0

Expert Reply:

In order to find the correct replacement leaf springs for a trailer you'll need to know the type (slipper/double eye), weight capacity, and unloaded length. The springs will stretch over time so the new replacements will be shorter. If you have a 3,500 lb axle with double eye springs then you'll likely need 3-Leaf Double-Eye Spring part # e59SR which measure 23-1/8" long.

expert reply by: Conner L

0

Answer 1

Hey Jeremy, For stainless steel lug nuts I'd go with Lionshead's 1/2" -20 #LHLR103 or 9/16"-18 #LHLR110 depending on the diameter of your wheel studs. You could add in a hub cover but it's honestly not necessary and more so just…

view full answer...

Answer 2

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 3

We do offer reverse lockout solenoids like the #DM11993. Since the Solenoids are a universal design it will work for the surge braker actuator on your Shoreland'r trailer. You will need to change the 4-way connector on your trailer to the #20017,…

view full answer...

Answer 4

Yes, the temperatures you mentioned are normal. If you were getting over 200 degrees that would be a bad sign. But typically if all of the hubs are the same temperature you're good and it's only really an issue if one of the hubs is hotter…

view full answer...

Answer 5

Thank you for the information! To replace your hub-and-rotor assembly I recommend using the Kodiak 10" Hub-and-Rotor Assembly #KHR10D which has the 5 on 4-1/2" bolt pattern you're needing as well as a Dacromet finish which is much more…

view full answer...

Answer 6

We don't know for sure what parts come on specific coaches, but we do carry some different handles that might work for you. If you've got a handle that screws in from the top then you can use the Replacement Handle for LaSalle Bristol…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Correct Replacement Leaf Springs for Trailer with Dexter 3,500 Lb Axle

Product Page this Question was Asked From

Continue Researching