Does Bunk Board Carpet Need to be Glued and Stapled

Question

Question:

Do you recommend a glue when attaching the carpet to the boards along with S.S. staples? If so, what is the best kind ? Thanks!

asked by: Toby T

1

Helpful Expert Reply:

It's not needed to glue the bunk board carpet like # CE11349 as well as staple it. With just staples you'd be fine.

expert reply by: Jameson C

1

Answer 1

In regards to the Square Jack with Footplate part #MJSQ-2500B, the overall dimensions of the jack are 24-3/4" tall while retracted or 40-1/8" tall while extended x 2-1/4" wide at the body. I have attached some other common dimensions…

view full answer...

Answer 2

We do have a large selection of replacement parts available for your Titan Model 10 Actuator. I am not sure exactly what you are needing so I will list out the replacement parts for you to check out. Replacement Master Cylinder Assembly - #T2374600…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Hey Terry, if you can get me two dimensions I'll be able to let you know what cushioned equalizer and shackle kit you'd need. I would need to know the distance between the axle centers (the wheelbase) and then also the distance between bolt…

view full answer...

Answer 10

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 11

Hey Don, thanks for the information! That's a significant amount of sag and a pretty heavy trailer, I recommend the Hellwig Pro Series Helper Springs item #HE79FR for the higher 2,500 lbs capacity. I doubt you're driving around with your bed…

view full answer...

Answer 12

Hey Rick, thanks for reaching out. I see you already got your order placed but I wanted to make sure your question was answered. Yes, you can cut the 4-way plug off the #BLU92HR and wire it to a 6-pin or 7-pin plug. People actually do this all the…

view full answer...

Does Bunk Board Carpet Need to be Glued and Stapled

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching