What is Silver Lever on Bottom of Motor of Stromberg Carlson Jack SC63VR

Question

Question:

What on warth id the leaver on the sode bottom for under the rubbee cover? The one that the little metal sleeve is for? Just read through the video script 4 times

asked by: Daniel G

0

Expert Reply:

On the bottom of the motor of the Stromberg Jack part # SC63VR there is a release lever setup that gets inserted when you want to manually crank the jack to release it basically from the motor.

expert reply by: Jameson C

0

Manual Crank
(click to enlarge)

Answer 1

I am sorry to hear about the functional issues you are having with your Stromberg Carlson Electric Trailer Jack #JET-3755. Based on the issue you are describing I would first manually lower the jack a little bit to make sure it was not overextended.…

view full answer...

Answer 2

The 3-bolt mounting flange on the Lippert Electric A-Frame Trailer Jack #LC285318 has a standardized hole pattern. This jack is intended to mount so that the included LED light faces forward toward the tow vehicle to illuminate the coupler and hitch…

view full answer...

Answer 3

Thread damage to the screw/nut inside of a jack is usually a result of over extending the trailer jack. I'm not saying that is what happened to you but that is the cause of the majority of these situations. Is your jack still covered under…

view full answer...

Answer 4

Hey Fred, I am very sorry to hear that your trailer jack keeps blowing fuses. If your Stromberg Carlson Jack #JET-3755 keeps blowing the 30A fuse, there are a few things to check that might help figure out the issue. First, take a look at the wiring.…

view full answer...

Answer 5

I reached out to the manufacturer, Stromberg Carlson, who told me their 3,500 lb Electric Trailer Jack #JET-3755 (Black) and #JET-3555 (White) has a travel speed of 10 inches over 55.5 seconds with no load. This is a relatively normal speed for a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 10

Hey Will! The square tube on the Bigfoot Hydraulic Trailer Jack #BF94FR is 4" x 4". What kind of trailer do you have?

view full answer...

Answer 11

Hey Brian! Yep, for your boat trailer, I’d skip the etrailer A-frame drill jack #e38AV since your trailer doesn't have that standard 3-bolt A-frame jack mount. That could be fabricated to fit, but that's a lot of unnecessary work. For a…

view full answer...

Answer 12

It sure does Steve! Our 3,500 lbs etrailer Electric Trailer Jack w/ Tongue Weight Scale item #e43KV also comes in a 5,000 lbs capacity. We have two different options depending on how you want to power it that I have listed below: Wired to Trailer -…

view full answer...

What is Silver Lever on Bottom of Motor of Stromberg Carlson Jack SC63VR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching