Replacement Shank For Blue Ox SwayPro Weight Distribution Hitch

Question

Question:

Will this work with the Blue ox sway pro hitch head?

asked by: Richard S

0

Expert Reply:

The Blue Ox Track Pro Weight Distribution Shank for 2-1/2" Hitches # BLU26FR that you referenced is for the Blue Ox Track Pro. Since you have the Blue Ox SwayPro system, you will want to go with Blue Ox SwayPro Weight Distribution Shank for 2-1/2" Hitches # BXW4028

expert reply by: Andrew N

0

Answer 1

When it comes to switching out your Reese distribution shank to a bigger one I would recommend going to The Blue Ox SwayPro Weight Distribution Shank for 2-1/2 inch Hitch - 9 inch Long - 9 Hole Adjustment #BXW4028. It is very similar to The Blue Ox…

view full answer...

Answer 2

So long as your F-250 has a 2-1/2" receiver then the B&W Tow & Stow 2-Ball Mount item #BWTS20037B will definitely work with your truck. This double ball mount has a 7,500 lbs capacity with the 2" ball or a 18,000 lbs capacity with…

view full answer...

Answer 3

Thanks for the picture! The longest weight distribution shank we have that fits a 2-1/2" hitch receiver is the Equal-i-zer Weight Distribution Shank item #EQ94FR. From hitch pin hole to the end of the shank is 12". It has a maximum tongue…

view full answer...

Answer 4

Your math is correct. Since the distance between the mounting holes of the Blue Ox weight distribution shank part #BLU26FR is the standard 1-1/4 inch and there is a total of 9 holes that would mean that there is 10 inches between the top and bottom…

view full answer...

Answer 5

No, it does not but there are a couple of options to make them work with a 2-1/2" receiver. The Blue Ox SwayPro Weight Distribution item #BXW1006 and item #BXW1000 are only sold with 2" shanks. The least expensive option is to use the Curt…

view full answer...

Answer 6

Hey Jorge, thanks for all of the info you listed on your weight distribution setup. Based on hearing that the correct shank you would want is the part #BXW4028 that you referenced. Using the lowest holes of this will allow your trailer to sit level…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Shank For Blue Ox SwayPro Weight Distribution Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching