Correct Hardware for Replacement Mounting Kit for etrailer and Ram Swivel Marine Jacks

Question

Question:

I would like to purchase MJ-1000B-Mk but I cant find the mounting hardware and the video says that you sell that separately but I cant find it. Could you provide me with a link or part number please. Thanks

asked by: Jesse R

0

Expert Reply:

The correct hardware kit for the Replacement Mounting Kit for etrailer and Ram Swivel Marine Jacks part # MJ-1000B-MK is the Replacement Mounting Hardware for etrailer and Ram Swivel Marine Jacks part # MJ-1000B-MBB.

expert reply by: Conner L

0

Answer 1

Replacement Mounting Hardware for etrailer and Ram Swivel Marine Jacks - 1,200 lbs and 1,500 lbs Item #MJ-1000B-MBB will actually be perfect for you. I checked the specs on the actual jacks that come with this hardware and it is basically identical…

view full answer...

Answer 2

For your retaining ring mounts on the trailer tongue, I recommend using the Brophy D-Ring Tie Down Anchor - Bolt-On - 2-3/8" Wide - Surface Mount - 4,000 lbs #LRB1. This is the strongest bolt on option we have. Anything stronger would require…

view full answer...

Answer 3

The Replacement Spring #4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Correct Hardware for Replacement Mounting Kit for etrailer and Ram Swivel Marine Jacks

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching