Which Roadmaster Rear Anti-Sway Bar for 2009 Fleetwood Tioga 31m Class C on Ford E-450 Chassis

Question

Question:

I own a 2009 Fleetwood Toiga 31m Is the Roadmaster Anti-Sway Bar - RM-1139-163 a good choice for this application

asked by: Frank M

0

Expert Reply:

I have a solution for you, but the Roadmaster # RM-1139-163 is not the correct fit for your 2009 Fleetwood Tioga. Instead, you'll need the # RM-1139-147.

I've linked an installation video of this for you to check out, as well.

expert reply by: Erik B

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

Hey Joel, we do have Roadmaster sway bars that fit the front and rear of your 2017 E-450 Class C Minnie Winnie with the part #RM-1139-189 for the front bar or part #RM-1139-147 for the rear. Hows the handling currently?

view full answer...

Answer 3

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 4

According to my Draw-Tite representative, the #6715 spare tire carrier should work with your 8-lug wheel as long as it doesn't weigh above 100 lbs.

view full answer...

Answer 5

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Which Roadmaster Rear Anti-Sway Bar for 2009 Fleetwood Tioga 31m Class C on Ford E-450 Chassis

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching