Easy to Install Brake Controller Recommendation for 2016 Nissan NV 3500

Question

Question:

I have a Nissan NV 3500 with a factory tow package. Will this kit numbet below be the easiest brake controller to install and include the factory harness that will be Plug and Play? No hardwiring needed? TK90160-3050-P About how long does it take to install?

asked by: Josh K

0

Expert Reply:

The Tekonsha brake controller part # TK90160 with the # 3050-P install harness is a really easy to install brake controller setup for your 2016 Nissan NV 3500. The only solution similar that might have a slightly more easy install is the P3 part # 90195 since it has a wider range of mounting directions compared to the # TK90160. I would think you could knock out the install in less than 30 minutes with most of the time being picking where to mount the controller on your dash.

expert reply by: Jameson C

0

Answer 1

Hey Thomas, thanks for reaching out! I really like the Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness #RED53CR because it comes with an adapter that plugs right into your factory wiring, and the main body of the controller can be hidden…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

Hey Jonathan, congrats on the new truck! The Universal Mounting Panel item #331-TPSI-001 is what you'll need to install the control knob of the Redarc Tow-Pro Liberty item #RED53CR in your 2026 Nissan Frontier SV. It measures 1-8/16" tall x…

view full answer...

Answer 12

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Easy to Install Brake Controller Recommendation for 2016 Nissan NV 3500

Continue Researching