Brake Controller and Wiring Recommendations for a 2015 Nissan NV 3500

Question

Question:

I am looking for a brake controller for my 2015 Nissan nv 3500.

asked by: Thomas W

0

Expert Reply:

Hey Thomas, thanks for reaching out!

I really like the Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness # RED53CR because it comes with an adapter that plugs right into your factory wiring, and the main body of the controller can be hidden virtually anywhere, just as long as you have access to the control knob.

If you have the factory tow package on your 2015 Nissan NV 3500 then you'll be set to go, otherwise you'll also need the Curt Wiring # C56148 and the Universal Wiring Kit # ETBC7 in order to get everything up and running.

What kind of trailer will you be towing?

expert reply by: Jon G

0

Tom

6/3/2025

I’m we are pulling a small camper

Jon G.

6/3/2025

@Tom Awesome! Any travel plans this year that you're excited for?

Tom

6/4/2025

@JonG Yes! We are going to Hocking Hills in Ohio and it is about a 4 hour trip for us. So I am making sure our NV3500 is fully ready and up for the job LOL

Jon G.

6/4/2025

@Tom I just looked up Hocking Hills and it looks absolutely beautiful! I'm excited for you now too! lol

Answer 1

That is correct. The #GS-2250DL is the direct replacement for your old grease seal marked P02860 on your 2019 Keystone Cougar.

view full answer...

Answer 2

Based on what I can find it shows the National seal 5970 is the same as the Timken 203034 which I see has an outer diameter of 3" and an inner diameter of 1.875". The only seal we have which meets these dimensions is the Seal #29031. You…

view full answer...

Answer 3

The Tekonsha brake controller part #TK90160 with the #3050-P install harness is a really easy to install brake controller setup for your 2016 Nissan NV 3500. The only solution similar that might have a slightly more easy install is the P3 part #90195…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Brake Controller and Wiring Recommendations for a 2015 Nissan NV 3500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching