How To Determine Correct Replacement Amber Lens for Optronics Clearance Light With Black Base

Question

Question:

I need to replace the amber lens cover for the side marker light on a 2018 Forest River Cedar Creek Fifth Wheel. It is made by Optronics, and the black base has the number 22368-022 on it. I am looking at your item number A32AB and not sure if this is the correct item.

asked by: John D

1

Helpful Expert Reply:

So I'm confident we have the correct replacement lens for you, but the 22368-022 isn't a part number, so in order to determine the correct lens, you'll need to do some quick measuring just to make sure you get the right one.

The first option is the you mentioned, the Replacement Amber Lens for MC32AB Trailer Lights # A32AB.

This is a replacement for the Trailer Clearance or Side Marker Light # MC32ABB, which is a one-wire light, and the replacement lens is 4" wide x 2" tall.

I have also added a link below to our entire selection of replacement lenses for Optronics clearance lights.

expert reply by: Kyle S

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 9

Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…

view full answer...

Answer 10

Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…

view full answer...

How To Determine Correct Replacement Amber Lens for Optronics Clearance Light With Black Base

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching