Recommended Method For Installing 7-Way Connector On 1996 Dodge Ram

Question

Question:

I believe I have located the factory under dash plug for the 7 blade though the wire colors to each port seem different than the colors on the vehicle specific adapter. I think this is expected. I currently have a four flat connector at the back of the truck. It seems like there was once a 7 blade on it, based on wires Im seeing under the truck and in the engine compartment. My intent is to run a new hot lead from the 7 blade to the battery. My question is about the blue wire from the 7 blade to the brake controller. The only blue wire I have found - that looks like it was cut at the connection point of an old 7 blade, terminates unconnected under the hood. This leads me to believe that the under dash plug may not work for connecting the brakes to the hitch. I think what I will need to do, but want to confirm, is: 1 Plug the 4 way into the ETBC7 2 Run the black wire through the circuit breaker to the battery 3 Cut the blue brake wire on the adapter connector at the under dash side, and splice the white ETBC7 wire run along with the black from the back, to the blue brake controller wire where I cut it from the connector. Does this sound correct? Thank you!

asked by: Mark

0

Expert Reply:

You have the right idea.

Since it appears that the factory wiring on your 1996 Dodge Ram has been cut, bypassing as much of it as possible will be a great idea to avoid headaches down the road.

Since you already have a 4-way connector you will plug it into the Universal Installation Kit for Trailer Brake Controller # ETBC7 as you mentioned and make the following remaining connections.

White wire grounded to vehicle frame
Blue wire to trailer brake controller
Black wire to vehicle battery with included 40 amp circuit breaker

Cutting the blue wire from your vehicle specific adapter for a trailer brake controller and using wire included with # ETBC7 to make the connection is exactly how we did it when we installed the # ETBC7 on a similar 2001 Dodge Ram.

I included a video of the # ETBC7 being installed on a 2001 Dodge Ram for you to take a look at.

expert reply by: Samuel C

0

Answer 1

If your 1998 Dodge Ram came with a factory installed 7-Way trailer connector, then you can use Curt harness #C56071. You would follow the factory connector's wiring harness forward under the vehicle to where it plugs in. The connector should be…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Recommended Method For Installing 7-Way Connector On 1996 Dodge Ram

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching