Is Transmission Cooler Needed to Tow 2500 Lb Trailer With 2011 Honda Odyssey
Updated 01/02/2021 | Published 12/31/2020
Products Featured in This Question
Question:
I want to add a receiver hitch on my 2011 Honda Odyssey. I would be pulling a single axle 14 trailer, carrying a Honda Pioneer 1000, so totally loaded, about 2500+ pounds. Never more than 2 occupants when towing. Most trips less than 100 miles one way, and mostly flatland driving. Do I need to be concerned about adding a tranny cooler
asked by: John E
Expert Reply:
From my research, I found that the 2011 Honda Odyssey has a 3500 lb towing capacity, so it will be able to handle the trailer and load you describe.
You might be fine without a transmission cooler for shorter trips on flat terrain, but I'd honestly suggest going with a cooler anyway, especially as the owner's manual recommends adding one to achieve the 3500 lb towing capacity. A cooler like # D13503 would provide extra protection for your transmission. The cooler doesn't cost much and the installation is pretty straightforward as shown in the linked install video.
For a hitch, I'd recommend the Curt Class IIl Hitch, part # C13068. You'll also need a trailer wiring harness such as part # 118521, a ball mount like # D-28 and a # PC3 hitch pin and # 19260 for a 1-7/8 inch trailer ball or # 63845 for a 2 inch ball.
I've also linked to install videos for the hitch and the trailer wiring harness.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Transmission Cooler
- Shop: Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class III - Efficient
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Install: Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets on a 2013 Honda Odyssey
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: How to Choose a Trailer Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Clean Up Your Trailer Wiring
- Article: Trailer Wiring Diagrams
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Search Results: trailer tires and wheels
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Q&A: Recommended SnapPad Jack Pads for a HWH Leveling System on a Motorhome
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: trailer jack
- Article: How to Choose the Right Trailer Hitch Class
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Hitch
