Replacement L-Brackets for Fastway Weight Distribution System

Question

Question:

Do you carry parts for fastway friction away L bracket parts

asked by: Joe F

0

Expert Reply:

Yes we do have replacement L-brackets for Fastway weight distribution systems like the part # FA93-02-5150 for the l-bracket, part # FA92-03-9205 for the L-pin, and part # FA93-02-5350 for the outer link plate.

expert reply by: Jameson C

0

Answer 1

I checked the install instructions for the Fastway E2 Weight Distribution Systems and they state to torque the spring bar hangers that attach to the channels of the frame to 65 ft lbs. If you under tighten them the hangers may "walk" along…

view full answer...

Answer 2

According to Fastway all of the link plate bolts get tightened to 50-70 ft lbs of torque.

view full answer...

Answer 3

The Replacement Outer Link Plate #FA93-02-5350 is the bracket piece that you are needing for the Fastway e2 Weight Distribution #FA94-00-1061 that you have. I do recommend getting the Replacement Hardware Kit #FA92-02-9200 as this will have all the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Leon! Your 23" bed depth is typical for newer Silverado 1500 trucks and will not cause a clearance issue. The Demco Autoslide #DM94AV has adjustable height settings of 15-1/4", 16-1/2", or 18" to help you achieve the…

view full answer...

Replacement L-Brackets for Fastway Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching