Hitch For C5500 GMC Truck

Question

Question:

looking for a trailer hitch for my 2007 GMC C5500 TRUCK. Do you guys carry one for this truck?

asked by: Bill

0

Expert Reply:

For a commercial vehicle such as the GMC C5500 you will need an universal hitch such as the Curt # C97CR Class-5, with 2-1/2” receiver, and fitting frame beams 18” to 62” in width with a 20,000 pound tow capacity.

If you do not need one as wide you could select the 44” wide Curt # C37CR, or the 44” wide Curt # C99CR hitch with an 18” drop and 16,000 pound tow rating.

I have included links to each of these items.

expert reply by: Les D

0

Answer 1

The Curt Trailer Hitch Receiver part #C15312 is what I recommend as a replacement for the factory trailer hitch on a 2002 Chevrolet Silverado 2500HD. In regards to the bolt hole spacing, this will be a different for the Curt Trailer Hitch Receiver as…

view full answer...

Answer 2

We do not carry a kit to convert a top wind jack to a side wind. to do this you would need to purchase an entirely new side wind jack. I've linked our selection for you.

view full answer...

Answer 3

You are correct in that the follow leg does not need to change to convert your Ram jacks to a 2 speed setup. You'll need to replace the lead leg with the part #TJD2SP-12000SP-F which has a two speed input but the output shaft still spins same…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Hitch For C5500 GMC Truck

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching