What Bearing Buddy Can Fit Trailer Hub # 8-258-50UC1

Question

Question:

As stated I. The title why beating buddy fits these

asked by: Jon

0

Expert Reply:

The correct size Bearing Buddy to fit the trailer hub part # 8-258-50UC1 that you referenced is the # BB1980A or part # BB1980A-SS for stainless steel.

expert reply by: Jameson C

0

Answer 1

Yes you can use a Bearing Buddy on your current axle setup but you'll have to remove the zerk/grease fitting. What you have now is an EZ lube spindle which allows you to push grease through the middle of the spindle but you can install a Bearing…

view full answer...

Answer 2

To determine which hubs would be best for your boat trailer there are a few things you will need to look at; the axle capacity on your boat trailer, the inner bearing number, outer bearing number, grease seal number, the bolt pattern of your wheels,…

view full answer...

Answer 3

No parts are more critical for the dependable performance of your trailer than the bearings, races, and seals. To ensure that your trailer performs reliably, you should inspect the bearings, races, and seals and repack the bearings every 12 months or…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

What Bearing Buddy Can Fit Trailer Hub # 8-258-50UC1

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching